Refrigeration dryer WDF-5085 with filters – DN100, 84,750 l/min
Code: WDF-5085
Product detailed description
The WDF-5085 refrigeration dryer dries compressed air to a pressure dew point of +3 °C, i.e. water class 4 according to ISO 8573-1, and at the same time filters it with a built-in 1 µm pre-filter and 0.01 µm fine filter. It handles 84,750 l/min (5,085 m³/h) at 7 bar, operates in the range of 4 to 16 bar and connects via a DN100 flange; power supply 400/50 V/Hz.
Dry, clean air protects the compressed air network, air receiver, valves, pneumatic cylinders and tools against corrosion and water, and in a paint shop it prevents surface defects caused by moisture. Because both filters are inside the dryer, you do not need to buy or install a separate pre-filter and after-filter.
It belongs to the range of WALTER WDF refrigeration dryers with integrated filters: a dryer and two filters in one cabinet, a Digi-Pro controller and R134a refrigerant.
Technical parameters
| Parameter | Value |
|---|---|
| Flow rate at 7 bar | 5,085 m³/h (84,750 l/min) |
| Working pressure | 4 to 16 bar |
| Pressure dew point | +3 °C (water class 4 according to ISO 8573-1) |
| Built-in filters | WFS pre-filter 1 µm, WFC fine filter 0.01 µm |
| Connection | DN100 |
| Power supply | 400/50 V/Hz |
| Pressure drop | 320 mbar |
| Refrigerant | R134a |
| Inlet air temperature | up to +60 °C |
| Room temperature | +4 to +50 °C, indoor installation only |
| Condensate drainage | solenoid valve with timer relay, manual button |
| Control | Digi-Pro controller and main switch |
| Circuit protection | high pressure switch 25 bar with manual reset, fan pressure switch 9–12 bar, refrigerant temperature sensor 45 °C |
| Dimensions L × W × H | 1,647 × 1,077 × 2,005 mm |
| Weight | 696 kg |
Dimensions and connections
Length 1,647 mm, width 1,077 mm, height 2,005 mm, weight 696 kg (according to the manufacturer). The air is connected via DN100 flanges. Keep the space clear around the grilles through which the condenser cooling air flows.
How it works
In the heat exchanger, the air is first pre-cooled by the dry air leaving the dryer, then the refrigerant cools it to a dew point of +3 °C and the water vapour condenses. The centrifugal separator separates the droplets and the condensate drains away. At the outlet, the dry air is warmed up again and passes through the pre-filter and fine filter.
Filters and controller
The WFS 1 µm pre-filter and WFC 0.01 µm fine filter capture solid particles and oil aerosol. The Digi-Pro controller displays the pressure dew point, signals alarms (high and low temperature, pressure, sensor failure) and uses the FIL alarm to remind you to replace the filters – always replace both elements; without an alarm, replace them once a year. The condensate is discharged by a timer-controlled valve, and manually with the MANUAL DRAIN button.
Alarms on the display
| Code | Meaning |
|---|---|
| tAL | low temperature in the refrigerant circuit |
| tAH | high temperature in the refrigerant circuit |
| FIL | time to replace the filter elements |
| hSE | general inspection due |
| HP | high pressure in the refrigerant circuit |
| Pr1 | temperature sensor failure |
| hFI | the dryer has reached its permitted operating time (operating hours) |
| tSH | high temperature in the compressor suction line |
Installation and maintenance
- place it on a level surface indoors and leave at least 50 cm around it for servicing and the flow of cooling air
- the room temperature should be +4 to +45 °C (technical limit +50 °C), with no chemicals that attack copper and aluminium
- keep the condensate drain free, without any narrowing or back pressure
- leave the main switch permanently on so that the crankcase heater of the refrigeration compressor works; after a longer period of inactivity, let the dryer warm up for at least 4 hours before starting
- only switch the dryer off when no air is flowing through it
- clean the condenser once a month and the condensate drain filter every 6 months
- replace the filter elements after the FIL alarm, or once a year without an alarm – always both
Where it is suitable
- pneumatic tools: impact wrenches, spray guns and blow guns
- paint shops and powder coating
- car repair shops and tyre services
- joinery and metalworking workshops
- CNC machines, pneumatic cylinders and valves of automated lines
- laboratories and metrology
Position in the system
The dryer goes downstream of the compressor and air receiver. The inlet air may be at most +60 °C; cool warmer air with an aftercooler first. It does not need a separate pre-filter or after-filter; for air free of odours and oil vapours, add an activated carbon filter downstream of it. For a dew point below 0 °C, you need a desiccant dryer.
For other sizes, see WDF refrigeration dryers.
Additional parameters
| Category: | Compressed Air Moisture Removal Air Dryers |
|---|---|
| Pressure: | 16 bar |
| Connecting: | flange DN100 |
| Mains voltage: | 400/50 V/Hz |
| Noise: | 45 dB(A) |
| Dimensions: | 1,647 × 1,077 × 2,005 mm |
| Weight: | 696 kg |
| Filtration: | 1 µm, 0.01 µm |
| Condensate discharge: | Automatic, Timed drain |
| Flow: | 84,750 l/min |
| ISO class: | x/4/x - ISO 8573.1 |
| Equipment: | Bleeding by time valve, Control unit LED display, Filtration, Automatic draining of condensate |
| Refrigerant: | Refrigerant R134a |
| Pressure dew point: | +3 °C |
| Dryer type: | Condensation dryer |
| Filtration stage: | Dust filter 1 µm, Microfilter 0.01 µm |
Product rating
Be the first who will post an article to this item!
WALTER Kompressortechnik - Innovative Solutions for Compressors
- About the company WALTER: WALTER Kompressortechnik is a renowned manufacturer of air compressors and accessories, known for its quality, reliability and innovative technologies. The company focuses on providing highly efficient solutions for various industries.
- Product portfolio:
- Screw compressors: we offer a wide range of screw compressors that are designed for maximum energy efficiency and long life. Ideal for high demanding industrial applications.
- Reciprocating compressors: these compressors are robust and reliable, suitable for smaller applications and workshops where high flexibility and low running costs are required.
- Mobile compressors: lightweight and easily portable compressors that allow easy use in a variety of locations, ideal for construction and field work.
- Scroll and special compressors: provide quiet operation and are suitable for specific applications requiring minimal vibration and noise.
- Innovation and quality: WALTER emphasizes continuous development and improvement of its products to ensure maximum customer satisfaction. Their compressors are equipped with advanced technologies to optimise performance and save energy.
- Customer support and service: the company offers comprehensive service, including installation, maintenance and diagnostics, ensuring the long-term reliability and efficiency of their equipment.
