Compressor oil sight glass: checking the oil level

An oil sight glass is the window you check the pump’s oil level through. It screws into the side of the oil sump and shows how much oil is in the machine. Once it yellows, clouds over or cracks, the level check stops working — and running a piston compressor without an eye on the oil ends with a seized pump. You pick it by the thread; the table below gives the outer diameter, the spanner size and the tightening torque for each one.
Pick it by the thread
The thread decides — it has to match the hole in the oil sump. The other dimensions are here so you know whether the sight glass will fit the space and what spanner it takes. The outer diameter is the largest dimension of the part, the window is the diameter you see the level through, and the spanner size is the hexagon across the flats.
| Oil sight glasses for compressors — dimensions, spanner size and tightening torque | ||||||
|---|---|---|---|---|---|---|
| Order code | Thread | Outer diameter | Window | Spanner | Thread length | Tightening torque |
| 13651 | G 1/4" | 18 mm | 9 mm | 15 mm | 10 mm | 2–3 Nm |
| 13671 | G 3/8" | 22 mm | 11 mm | 19 mm | 7.5 mm | 3–5 Nm |
| 13691 | G 1/2" | 26 mm | 14 mm | 22 mm | 10.5 mm | 4–6 Nm |
| 13721 | G 3/4" | 31.5 mm | 20 mm | 27 mm | 10.5 mm | 6–8 Nm |
| 13741 | G 1" | 40 mm | 25 mm | 34 mm | 11 mm | 8–10 Nm |
| 13761 | G 1 1/4" | 47 mm | 30 mm | 40.5 mm | 11.5 mm | 8–10 Nm |
The dimensions and torques come from the manufacturer’s datasheet, which is attached to every product. Keep to the torque — over-tightening cracks the window, under-tightening leaks.
#showmore#
What it does and what destroys it
A magnifying lens
The window is shaped as a magnifying lens, so the level stays readable even from the side — on a compressor you cannot comfortably reach from the front, that is what decides. Inside sits a contrast star of matt anodised aluminium with a red centre dot; the level reads better against it than against bare glass.
Material and temperature
The body is transparent polyamide-based technopolymer (PA-T), the seal is synthetic NBR rubber. The maximum continuous working temperature is 100 °C, which is ample for a piston compressor.
Keep alcohol away
This is the one thing that will reliably destroy a sight glass: it must not come into contact with alcohol or with cleaning agents containing alcohol. The technopolymer crazes afterwards. When wiping oil from around the sight glass, use a rag and an alcohol-free degreaser — not a spirit-based glass cleaner.


When and how to replace it
When it is time
When the window has yellowed, clouded over or cracked, the level cannot be read from it — and the oil check is the only reason it is there. The second reason is a leak: oil weeping around the sight glass usually means a hardened seal.
How to do it
Drain the oil or tilt the machine so the level sits below the opening. Unscrew the old sight glass, wipe the seating face dry and screw the new one in with its seal. Tighten to the torque from the table — by hand and by feel it is easy to overdo, and the plastic body cracks.
What goes with it
While the machine is standing anyway, these usually come in handy.
- Compressor oils — when you change the fill along with the sight glass
- Service kits — gaskets, filter and oil for one service in one box
- Compressor pumps — the sight glass fits the pump’s oil sump
- Intake filters — the other thing checked at every service
Ventilek says
A yellowed sight glass is a cheaper problem than a seized pump.
Folks, this is a part worth pennies that the whole machine hangs on. When you cannot see through the window, nobody checks the level — and one day the pump seizes because there was no oil in it. Two pieces of advice. First: replace it at the next service, not "sometime". Second: tighten it to a torque, not by force — the plastic body cracks before you notice. And never a spirit cleaner on it.
Frequently asked questions about oil sight glasses
- How do I tell which size I need?
- By the thread in the oil sump. Unscrew the old sight glass and measure the thread, or compare it with the table above — we stock six sizes from G 1/4" to G 1 1/4". All of them have a G pipe thread.
- What do I tighten the sight glass with?
- By the hexagon on the body, with a spanner to suit the size — from 15 mm on the G 1/4" to 40.5 mm on the G 1 1/4". Both the spanner size and the torque are in the table above. Keep to the torque: the plastic body is easy to overtighten.
- Can I clean it with spirit or glass cleaner?
- No. The technopolymer must not come into contact with alcohol or with cleaning agents containing it — they craze the material. Use a rag and an alcohol-free degreaser.
- What temperature will the sight glass take?
- The maximum continuous working temperature is 100 °C. A piston compressor will not reach that in the oil sump, so there is plenty of margin.
- Do I have to drain the oil to replace the sight glass?
- It is enough for the level to sit below the opening. Either drain the oil or tilt the machine. And once the oil is out, it pays to renew the fill at the same time.
- Is a seal included?
- Yes, the sight glass comes with an NBR seal. Do not reuse the old one — hardened rubber is the most common reason oil weeps around a sight glass.
Dimensions, material and tightening torques follow the manufacturer’s datasheet, which is attached to every product. All dimensions are in millimetres.
Product sorting
List of products
A replacement oil sight glass for a compressor with a G 3/8" pipe thread. Outer diameter 22 mm, window 11 mm, tightened with a 19 mm spanner. Transparent PA-T technopolymer...
A replacement oil sight glass for a compressor with a G 1 1/4" pipe thread. Outer diameter 47 mm, window 30 mm, tightened with a 40.5 mm spanner. Transparent PA-T technopolymer...
A replacement oil sight glass for a compressor with a G 1/4" pipe thread. Outer diameter 18 mm, window 9 mm, tightened with a 15 mm spanner. Transparent PA-T technopolymer body,...
A replacement oil sight glass for a compressor with a G 1/2" pipe thread. Outer diameter 26 mm, window 14 mm, tightened with a 22 mm spanner. Transparent PA-T technopolymer...
A replacement oil sight glass for a compressor with a G 1" pipe thread. Outer diameter 40 mm, window 25 mm, tightened with a 34 mm spanner. Transparent PA-T technopolymer body,...
A replacement oil sight glass for a compressor with a G 3/4" pipe thread. Outer diameter 31.5 mm, window 20 mm, tightened with a 27 mm spanner. Transparent PA-T technopolymer...