Compressor oil for piston and screw machines

Oil in a compressor does more than lubricate bearings. In a piston machine it seals between piston and cylinder and carries heat away from the head; in a screw machine it also seals the gap between the rotors and cools the whole block — which is why several litres circulate through it and why it is called oil-cooled. That is also why oil from a piston machine does not belong in a screw machine, and the other way round. It is chosen by compressor type, duty and ambient temperature, not by the brand of the machine.
Piston or screw? That is where the choice starts
Oil does a different job in each of those two machines, which is why it is made separately. They cannot be swapped — not because the manufacturer forbids it, but because each of them does something the other cannot.
Oil in a piston compressor
It lubricates the connecting rod and the cylinder wall, seals around the piston rings and carries heat away from the head. It works in impacts — on every stroke it is compressed and heated. What it needs above all is resistance to oxidation, so that carbon does not build up on the check valve and the discharge line. A crankcase holds a quarter of a litre to five litres of it.
Oil in a screw compressor
It lubricates the rotor bearings, seals the gap between the rotors and above all carries heat out of the compressed air. It circulates through the cooler and the separator, so the machine holds several litres of it and it never stops moving. What it needs above all is not to foam and to separate cleanly from the air in the separator.
Why they cannot be swapped
Oil for piston machines is built for short impact loads and is not made to be separated from air — in a screw machine it would clog the separator. Oil for screw machines, in turn, has a different viscosity from the one a piston unit needs to keep the cylinder sealed.
Mineral or synthetic compressor oil
Mineral oil comes from refining crude and is the standard fill in most machines. It handles ordinary duty in a clean environment and costs noticeably less. On screw compressors it will last you 2,000 running hours with the basic Rotair range, or 4,000 running hours with the heavily additised Rotair Plus and SC Oil 46 M.
Synthetic oil is made by chemical synthesis, so its molecules are all the same size and it holds its properties where mineral oil is already ageing. Rotair Xtra manages 8,000 running hours and an ambient temperature up to +46 °C. On piston machines you reach for it in multi-shift duty (Altair Plus) or in industry (Altair Ultra). It costs more, but on a machine that runs all the time the longer interval and lower wear pay it back.
Food grade oil solves something else entirely than endurance. Rotair Foodgrade carries NSF H1, halal and kosher certification and is meant where a trace of oil in the air must not contaminate the product — pharmaceutical production, food and beverage, and electronics. Its interval is 2,000 running hours and its ambient limit 30 °C, exactly the same as the basic mineral oil. Being safe for incidental contact is paid for with a shorter life, not a longer one.
What the packs look like
From a bottle for a single top-up to a drum for a workshop with several machines. Pack size says nothing about the quality of the oil — it follows only from how much of it you will use.




Compressor oil overview
| Oils for piston and screw compressors — structure, change interval and pack size | |||||
|---|---|---|---|---|---|
| Order No. | Oil | Structure | What operation it's for | Replacement | Packaging |
| ALTP-0-25 | Altair Pro | mineral | light duty up to 500 h a year | — | bottle 0.25 l |
| ABP-1 | ABAC Pro | mineral | ABAC Line L/V and A29/A39 | — | bottle 1 l |
| ALT-1 | Altair | mineral | daily use in a workshop | — | bottle 1 l |
| ALT150-5 | Altair 150 | mineral | multi-shift duty in industry | — | 5 l canister |
| ALTPL-5 | Altair Plus | synthetic | multi-shift duty, high temperature | — | 5 l canister |
| ALTU-1 | Altair Ultra | synthetic | industrial compressors | — | bottle 1 l |
| ALTU-5 | Altair Ultra | synthetic | industrial compressors | — | 5 l canister |
| ATM-OIL | ATMOS VDL-10+ | mineral | ATMOS piston compressors | — | bottle 1 l |
| 2XATM-OIL | ATMOS VDL-10+ | mineral | ATMOS piston compressors | — | bottle 2 × 1 l |
| WK1-OIL | WALTER WKTT | mineral | WALTER piston compressors | — | bottle 1 l |
| WK5-OIL | WALTER WKTT | mineral | WALTER piston compressors | — | 5 l canister |
| BWL-1 | Black Wind | mineral | Black Wind piston compressors | once a year or after 100 engine hours | bottle 1 l |
| RTR-5 | Rotair | mineral | mild environment, up to 30 kW | 2,000 MH | 5 l canister |
| RTR-20 | Rotair | mineral | mild environment, up to 30 kW | 2,000 MH | 20 l canister |
| RTR-209 | Rotair | mineral | mild environment, up to 30 kW | 2,000 MH | 209 l drum |
| RTP-5 | Rotair Plus | mineral | higher temperatures, longer intervals | 4,000 MH | 5 l canister |
| RTP-20 | Rotair Plus | mineral | higher temperatures, longer intervals | 4,000 MH | 20 l canister |
| RTP-209 | Rotair Plus | mineral | higher temperatures, longer intervals | 4,000 MH | 209 l drum |
| RTX-5 | Rotair Xtra | synthetic | hardest industry and heat | 8,000 MH | 5 l canister |
| RTX-20 | Rotair Xtra | synthetic | hardest industry and heat | 8,000 MH | 20 l canister |
| RTX-209 | Rotair Xtra | synthetic | hardest industry and heat | 8,000 MH | 209 l drum |
| RTF-5 | Rotair Foodgrade | food grade | food, pharma, electronics | 2,000 MH | 5 l canister |
| RTF-20 | Rotair Foodgrade | food grade | food, pharma, electronics | 2,000 MH | 20 l canister |
| RTF-209 | Rotair Foodgrade | food grade | food, pharma, electronics | 2,000 MH | 209 l drum |
| SCO-5L | SC Oil 46 M | mineral | SCR screw compressors | 4,000 MH | 5 l canister |
| SCO-20L | SC Oil 46 M | mineral | SCR screw compressors | 4,000 MH | 20 l canister |
| SCO-209L | SC Oil 46 M | mineral | SCR screw compressors | 4,000 MH | 208 l drum |
| OLN-1 | M7 | — | air tools, ISO VG 32 | — | bottle 1 l |
The manufacturer states a change interval only for screw compressor oils, and it applies at normal temperature and humidity and in a dust-free environment — heat, damp or dust shorten it. On piston machines the oil is not changed by the oil but by the machine manual; usually the first change comes after running in, then once a season or after a set number of running hours. Under the “Tell me more” button you will also find a table of oil capacities for individual compressors, an oil selector by environment and the change procedure.
#showmore#
How much oil your compressor takes
The most common question before buying. For ABAC piston compressors the manufacturer states the oil capacity for every model separately — and which oil belongs in it. The figures are for a full change, that is after the old oil has been drained.
| Compressor | Oil charge | Recommended oil |
|---|---|---|
| A29 | 0.478 l | Altair Pro |
| A29B | 0.478 l | Altair Pro |
| A29BX | 0.478 l | Altair Pro |
| A39 | 0.889 l | Altair Pro |
| A39X | 0.889 l | Altair Pro |
| A39B | 0.889 l | Altair Pro |
| A49B | 1.111 l | Altair |
| B20 | 0.244 l | Altair Pro |
| B26 | 0.389 l | Altair Pro |
| B26B | 0.389 l | Altair Pro |
| B49 | 1.444 l | Altair |
| B49B | 1.444 l | Altair |
| B59 | 1.667 l | Altair |
| B59B | 1.667 l | Altair |
| B60 | 2.556 l | Altair |
| B70 | 4.000 l | Altair |
| B79 | 5.111 l | Altair |
| BV89 | 5.111 l | Altair |
| CA1 | 1.500 l | Altair |
| CA2 | 1.500 l | Altair |
| L20 | 0.222 l | Altair Pro |
| L25P | 0.278 l | Altair Pro |
| L30P | 0.278 l | Altair Pro |
| V30 | 0.500 l | Altair Pro |
| V36 | 0.500 l | Altair Pro |
The figures come from the technical documentation of the ABAC piston compressor manufacturer. Always buy a little more than the capacity — some oil stays on the crankcase walls and a reserve is useful for topping up. For a machine holding 0.478 l a 1 l bottle is enough; for a B70 with four litres a 5 l canister is the better buy. For screw compressors and other brands the capacity is in the machine manual, or we will gladly look it up for you.
Which Rotair for your conditions
On ABAC SPINN screw compressors it is not only the hours the machine runs that decide, but also how warm, humid and dusty the compressor room is. The manufacturer put it into a single table: find your row, and the column for your annual running hours names the oil to choose.
| Ambient temperature | Humid environment | Dusty environment | Operating demands | 2,000 MH/year | 4,000 MH/year | 8,000 MH/year |
|---|---|---|---|---|---|---|
| up to 30 °C | no | no | mild | Rotair | Rotair Plus | Rotair Xtra |
| up to 30 °C | yes | no | mild | Rotair | Rotair Plus | Rotair Xtra |
| up to 30 °C | no | yes | mild | Rotair | Rotair Plus | Rotair Xtra |
| up to 30 °C | yes | yes | medium load | Rotair Plus | Rotair Xtra | Rotair Xtra |
| 30 to 40 °C | no | no | medium load | Rotair Plus | Rotair Xtra | Rotair Xtra |
| 30 to 40 °C | yes | no | medium load | Rotair Plus | Rotair Xtra | Rotair Xtra |
| 30 to 40 °C | no | yes | medium load | Rotair Plus | Rotair Xtra | Rotair Xtra |
| 30 to 40 °C | yes | yes | high load | Rotair Xtra | Rotair Xtra | Rotair Xtra |
| above 40 °C | — | very dusty | high load | Rotair Xtra | Rotair Xtra | Rotair Xtra |
Heavily dusty covers mining, cement works, metalworking, steelmaking and foundries. Normal dust means food and beverage, automotive, electronics manufacturing or petrochemicals. Judge humidity by whether the compressor room is damp for most of the year.
Technical values of Rotair oils
All four Rotair oils are viscosity grade ISO VG 46. What differs is how much they take — and that shows in the viscosity index and the pour point. The higher the index, the less the oil changes thickness with temperature.
| Oil | Structure | Replacement | Ambient temperature | Viscosity index | Pour point | Colour |
|---|---|---|---|---|---|---|
| Rotair | mineral | 2,000 MH | 0 to 30 °C | 98 | -33 °C | light brown |
| Rotair Plus | mineral | 4,000 MH | 0 to 35 °C | 102 | -33 °C | clear to light brown |
| Rotair Xtra | synthetic | 8,000 MH | 0 to 46 °C | 133 | -57 °C | clear |
| Rotair Foodgrade | food grade | 2,000 MH | 0 to 30 °C | 134 | -57 °C | clear |
Despite being synthetic, Rotair Foodgrade has the same interval and the same temperature ceiling as the basic Rotair — its advantage is safety, not endurance. The basic Rotair is recommended for compressors up to 30 kW.
Changing the oil step by step
Oil is drained warm, shortly after the machine is shut down. Warm oil flows and takes the dirt with it; in cold oil that dirt stays sitting on the bottom. The machine must be depressurised and disconnected from the mains. On screw compressors the oil filter and separator are changed together with the oil — otherwise within a few dozen hours the new oil is fouled again by what was left in the old filter.
Mineral and synthetic must never be mixed
Never mix mineral oil with synthetic. Their additive packages may not get along and a thick sludge can form in the machine that blocks both the filter and the separator. When you change the type of oil or the brand, the machine has to be flushed: drain the old oil warm, fill with new, let the machine run briefly off load, drain again, replace all filters and the separator — and only then put in the final fill.
Air tool oil is a different oil
Impact wrenches, grinders, breakers and other air tools need a thin oil delivered with the air itself. It goes into a lubricator fitted into the line ahead of the tool, which carries it on as a fine mist. Compressor oil does not belong in a lubricator — it is far too thick to atomise. We stock the OLN-1 oil in viscosity grade ISO VG 32.
Lubricators and automatic lubricators are in a separate category. Oil in a tool has two jobs: it lubricates the vanes of the rotary motor and protects it from corrosion and icing. As the air expands in the tool it cools sharply and drops out moisture; without oil, rust settles on the vanes and the tool loses power. That is exactly why a lubricator takes a low viscosity oil that does not stiffen on cold metal.
Where to next
Oil is only one part of servicing. Here is the rest of what proper maintenance involves.
- Oil selection guide — goes through the choice in more detail than this page
- Oils in screw compressors — why oil in a screw machine both cools and seals
- Service kits — oil and filters together so nothing is forgotten
- Sight glasses — check the level without taking the machine out of service
- Service and support — for when you would rather not do the change yourself
Ventilek advises
Never pour car engine oil into a compressor.
This is the most common mistake I see. Engine oil is built to cope with soot from fuel — it carries detergents a compressor has no use for. What it does do is foam, and in a machine where the oil is thrown against rotors or splashed around a crankcase that is exactly what you do not want. Foamed oil neither lubricates nor cools. And one more thing: on a screw machine watch the running hours like a hawk. An oil and filter change costs a few hundred. A screw block seized by degraded oil costs tens of thousands.
Frequent questions about compressor oil
- Can I put engine oil in a compressor?
- No. Engine oil carries detergents meant for fuel soot that a compressor does not need, and above all it foams. Foamed oil neither lubricates nor carries heat away. In a screw machine it also cannot be separated from the air and will clog the separator.
- How do I know it is time for a change?
- On screw compressors by running hours — the machine counts them itself and the manufacturer quotes 2,000 to 8,000 running hours depending on the range. On piston machines you follow the machine manual. By eye: oil that has gone black, thickened or smells burnt comes out regardless of the counter.
- What happens if I mix mineral and synthetic oil?
- Their additive packages may not get along and a thick sludge can form that blocks the oil filter and the separator. When moving to a different type or brand the machine has to be flushed and all filters replaced.
- How much oil should I buy?
- A little more than the machine holds — some oil stays on the walls and a reserve is useful for topping up. Capacities for ABAC piston compressors are in the table above; for other machines the volume is in the manual.
- Do I need a special oil in a food plant?
- If the compressed air meets food, packaging or medicine, then yes — food grade oil is safe for incidental contact should a trace of it reach the air. Bear in mind its change interval is 2,000 running hours, the same as the basic mineral oil.
- Is oil for piston and screw compressors really different?
- Yes. In a screw machine the oil seals the gap between the rotors, cools the whole block and has to separate from the air. In a piston machine it keeps the cylinder sealed and takes impact loading. Each is built for a different job, and swapping them shortens the life of the machine.
Change intervals are quoted by the manufacturer for normal temperature and humidity and a dust-free environment. Oil capacities apply to ABAC piston compressors according to the manufacturer’s technical documentation.
Product sorting
List of products
A one-litre bottle of the oil the manufacturer specifies for ABAC Line L/V machines and the single-stage A29 and A39. On most of them one pack covers a full change.
A quarter-litre bottle for small compressors that are not used every day. It fits in the case with the tools and does not leave you half a canister standing in the workshop for...
A twenty-litre canister of an oil with twice the interval of the basic Rotair and still not synthetic. The commonest choice for ordinary industrial duty.
The all-round oil for a compressor used in the workshop every day. A grade tougher than the entry Altair Pro, but not yet the industrial range.
An oil for compressor rooms that get hot in summer. It holds its properties where mineral oil starts to thicken and darken before the interval is up.
The genuine oil for WALTER cast-iron GK pumps. The one-litre bottle suits topping up, and a full change on the smallest pump.
A five-litre canister for compressors running several shifts. One pack covers a full change even on the largest ABAC piston machines.
A cost-effective alternative to original lubricants. For machines out of warranty, where the price per litre is decisive — not for compressors still under warranty.
A twenty-litre canister of the basic Rotair oil. The usual choice for one workshop with one screw machine and an annual change.
A drum of a cost-effective alternative to original lubricants. For operations with several machines out of warranty, where the oil is changed in-house.
A twenty-litre canister of genuine SCR lubricant. The usual choice for one screw machine in a workshop or plant.
A drum of heavily additised Rotair Plus for plants that service their own machines. A longer interval than the basic Rotair, the lowest price per litre in the range.
The five-litre pack of genuine WALTER oil. It covers a full change on every GK pump including the largest GK1400.
A certified drum for food and pharmaceutical plants with several machines. The shorter interval means it is used up faster than in the other ranges.
The genuine SCR lubricant in the smallest canister. On a machine under warranty it is the only choice the manufacturer accepts.
The basic genuine oil for ABAC SPINN screw machines in the smallest canister. For compressor rooms that are neither hot nor damp nor dusty.
Air Tool Oil OLN-1 — oil for pneumatic tools. High-quality oil designed for lubricating air tools.
The genuine oil for Black Wind compressors. The manufacturer expects a shorter interval on these than on industrial machines, including a change after running in.
A drum of the basic Rotair oil for plants with several screw machines. Count on a pump or a tap — a full drum is not something you pour from.
The genuine oil for ATMOS Perfect and Perfect Line piston compressors. The viscosity is chosen for these machines, so there is no substitute to hunt for.
Two bottles of genuine ATMOS oil together. For Perfect machines from 4 kW upwards, where one bottle does not cover a change.
A heavily additised oil with twice the interval of the basic Rotair. A five-litre canister for smaller machines or for topping up.
A five-litre canister of the highest ABAC oil for piston machines. Unlike the one-litre bottle this is a pack for a full change, not just for topping up.
The top oil of the Rotair range in a five-litre canister. The only one the manufacturer allows into compressor rooms above 40 °C and into very dusty plants.
An oil safe for incidental contact, certified NSF H1, halal and kosher. For plants where the compressed air meets the product.
A twenty-litre canister for continuous duty. One change a year instead of four — filters and separator included.
A twenty-litre canister of certified oil for food plants. The usual choice for one line with its own screw compressor.
A drum of genuine SCR lubricant for plants with several machines. The lowest price per litre in the range, but it needs a stand and a pump.
A drum of the top Rotair range. For plants with several machines running continuously in heat or in dust.
The only oil in the ABAC range listed for industrial piston and screw machines alike. The one-litre bottle suits topping up rather than a full change.