PA6 polyamide tubing (nylon) for compressed air

PA6 polyamide (nylon) tubes are rigid plastic tubes with a high pressure resistance. They are intended for longer straight compressed air lines in industry and in automation, measuring and control technology.
They are resistant to salt water, oils, chemicals and ageing. The range has seven sizes from 4/2 to 12/10 mm in three colours and a working pressure of 15 to 56 bar depending on the diameter.
Diameters, pressures and order codes
The tube size is given as outer / inner diameter in millimetres. The outer diameter must match the fitting, the inner one determines how much air the tube passes. The picture shows all seven sizes of the PA6 range to the same scale.

| PA6 tubing — 7 sizes, 3 colours | |||||||
|---|---|---|---|---|---|---|---|
| Diameter D/d | Wall | Working pressure | Bend radius | Weight | Blue | Clear | Black |
| 4/2 mm | 1 mm | 56 bar | 25 mm | 11 g/m | PA42B | PA42N | PA42S |
| 4/2.5 mm | 0.75 mm | 38 bar | 30 mm | 9 g/m | PA425B | PA425N | PA425S |
| 5/3 mm | 1 mm | 42 bar | 30 mm | 15 g/m | – | PA53N | – |
| 6/4 mm | 1 mm | 33 bar | 45 mm | 18 g/m | PA64B | PA64N | PA64S |
| 8/6 mm | 1 mm | 24 bar | 65 mm | 25 g/m | PA86B | PA86N | PA86S |
| 10/8 mm | 1 mm | 19 bar | 80 mm | 32 g/m | PA108B | PA108N | PA108S |
| 12/10 mm | 1 mm | 15 bar | 100 mm | 39 g/m | – | PA1210N | PA1210S |
We sell the tubes by the metre, you only enter the length you need. A full roll is 100 m. The 5/3 mm size is made only in clear, and the blue 12/10 mm is no longer made.
#showmore#
High pressure in all diameters

PA6 polyamide is a rigid material, so even a tube with a 1 mm wall withstands a high pressure. The 4/2 mm tube withstands the most at 56 bar, the 12/10 mm the least at 15 bar.
Even the largest diameter therefore copes with the pressure of a standard workshop system with a margin. According to the manufacturer’s sheet, the working pressure is set with a threefold safety factor.
The values apply at room temperature. The working pressure falls as the temperature rises; according to the manufacturer’s chart, it is roughly halved at +80 °C. The 4/2.5 mm size has a thinner 0.75 mm wall, so it withstands less than 4/2 and 5/3 mm.
A rigid tube needs a wider arc

The rigidity that lets the PA6 tube withstand a high pressure also makes it less flexible. The minimum bend radius grows with the diameter from 25 mm for 4/2 to 100 mm for 12/10 mm.
That is why the range is intended mainly for longer straight lines. Solve a sharp change of direction with an L-fitting and keep the tube straight.
Where you need a smaller arc and a lower pressure is enough, a softer tube will do. The 6/4 mm size with a 30 mm bend radius and a pressure of 13 bar is offered by PE polyethylene tubes.
Which diameter to choose
The diameter is chosen according to the fitting on the valve or device and the required flow. With the PA6 range, it also matters how large an arc the tube has to make along its route.

4/2 and 4/2.5 mm
Control air, sensors and measuring connections. The 4/2 size withstands 56 bar, the 4/2.5 with a thinner wall passes more air. Other tubes with the same outer diameter are in the overview of 4 mm tubes.

5/3 mm
For devices with a 5 mm connection, only in clear. You connect it with a brass push-in fitting or a compression fitting with a union nut. Other materials in this diameter are in the overview of 5 mm tubes.

6/4 mm
The most common pneumatic size for valves and smaller cylinders. Pressure 33 bar, an arc with a radius of at least 45 mm. A comparison with other materials is in the overview of 6 mm tubes.

8/6 mm
Higher flow for cylinders and long supply lines. Pressure 24 bar, bend radius 65 mm. Other ranges of this diameter are in the overview of 8 mm tubes.

10/8 mm
A large inner diameter for machines with a higher air consumption, pressure 19 bar. A bend needs an 80 mm radius. More options are in the overview of 10 mm tubes.

12/10 mm
The highest flow in the range for main supply lines, still with a pressure of 15 bar. The bend radius is 100 mm. Other materials of the same diameter are in the overview of 12 mm tubes.
Three colours: what each is for
The colour does not change the properties of the tube; all three have the same pressure, temperature and bend radius. The 5/3 mm size is only available in clear, the 12 mm tube in clear and black.



Fittings, cutters and protection
PA6 tubes are connected with push-in fittings or compression fittings with a union nut. Cut the rigid tube square with a sharp cutter so that the cut is straight and free of burrs, and push it into the fitting all the way to the stop.

Plastic push-in fittings
Straight, T, L, Y and threaded for diameters 4, 6, 8, 10 and 12 mm.
View
Brass push-in fittings
Metal version for diameters 4 to 12 mm, including the 5 mm diameter.
View
Compression fittings with union nut
A secure joint for the exact tube size 4/2.5, 5/3, 6/4, 8/6, 10/8 and 12/10 mm.
View
Tube cutters
A square, burr-free cut so that the fitting seals all the way round.
ViewWhen to choose a different tube

Frost below −10 °C
PA6 works from −10 °C. For outdoor and freezing operation from −40 °C, use PA11 Rilsan tubes.

Frequent bending and movement
Where the tube bends with the movement of the machine or runs in many arcs, soft polyurethane is a better choice. A pressure of 10 bar in all diameters is offered by PUJ polyurethane tubes.

Heat above +80 °C
For hot environments and aggressive chemicals at temperatures up to +260 °C, use PTFE Teflon tubes.
Ventilek’s tip
With a PA6 tube, do not watch the pressure, watch the arc. There is a pressure margin in every diameter, but the minimum bend radius grows up to 100 mm.
- What pressure can the PA6 tube withstand?
- It depends on the size. The working pressure ranges from 15 bar for 12/10 mm to 56 bar for 4/2 mm and, according to the manufacturer’s sheet, is set with a threefold safety factor. The exact values are in the table above.
- Why does PA6 have a larger bend radius than soft tubes?
- PA6 polyamide is a rigid material with a hardness of 85 °Sh. Thanks to this, it withstands a high pressure but bends less easily. The minimum bend radius ranges from 25 mm for 4/2 to 100 mm for 12/10 mm.
- Does the pressure also apply at higher temperatures?
- Not in full. The values in the table apply at room temperature, and the working pressure falls as the temperature rises. According to the manufacturer’s chart, it is roughly halved at +80 °C.
- Why are some sizes not available in all colours?
- The 5/3 mm size is made only in clear. The blue 12/10 mm is no longer made; the same size is available in clear and black.
- Do you also sell lengths shorter than a full roll?
- Yes, we sell the tubes by the metre. A full roll is 100 m for all sizes.
Data according to the catalogue sheets of the PA6 range and the manufacturer’s sheet: dimensions, wall thickness, working pressure, bend radius and weight, working temperature −10 to +80 °C, material hardness 85 °Sh, safety factor 3 : 1, medium compressed air, material PA6 polyamide (nylon).
Product sorting
List of products
Black PA6 polyamide tube 8/6 mm with a higher flow. Working pressure 24 bar, resistance to oils and ageing.
Clear nylon tube 4/2.5 mm, translucent, with a 0.75 mm wall. Working pressure 38 bar for measuring and control lines.
Blue PA6 tube 4/2.5 mm with a 0.75 mm wall and a larger inner diameter. Working pressure 38 bar, sold by the metre.
Blue PA6 nylon tube 8/6 mm for larger cylinders and long lines. Working pressure 24 bar, bend radius 65 mm.
Black PA6 polyamide tube 12/10 mm with the highest flow in the range. Working pressure 15 bar, 1 mm wall.
Clear nylon tube 8/6 mm, translucent. Working pressure 24 bar, sold by the metre or as a full 100 m roll.
Black PA6 polyamide tube 10/8 mm for supply lines to machines. Working pressure 19 bar, inner diameter 8 mm.
Clear PA6 polyamide tube 10/8 mm, translucent. High flow and a working pressure of 19 bar.
Black PA6 polyamide tube 4/2.5 mm for control circuits with a higher flow. 0.75 mm wall, 38 bar.
Blue PA6 nylon tube 6/4 mm, the most common pneumatic size. Working pressure 33 bar, bend radius 45 mm.
Clear PA6 polyamide tube 6/4 mm, translucent. The standard pneumatic size with a working pressure of 33 bar.
Clear nylon tube 12/10 mm, the largest diameter in the PA6 range. Working pressure 15 bar, bend radius 100 mm.
Blue PA6 nylon tube 4/2 mm with a working pressure of 56 bar, the highest in the range. For control and measuring air, sold by the metre.
Blue PA6 nylon tube 10/8 mm with a large inner diameter. Working pressure 19 bar, bend radius 80 mm.
Black PA6 polyamide tube 4/2 mm for machine control circuits. Working pressure 56 bar, resistant to oils and ageing.
Clear PA6 polyamide tube 5/3 mm for devices with a 5 mm connection. Working pressure 42 bar, the only colour of this size.
Clear PA6 polyamide tube 4/2 mm, translucent. Working pressure 56 bar, for measuring and control connections.
Black PA6 polyamide tube 6/4 mm for pneumatic systems on machines. Working pressure 33 bar, resistant to oils.
The blue PA6 tube 12/10 mm is no longer made. The same size and a pressure of 15 bar are offered by the clear or black version.

