How to Choose a Compressor for a Tire Service

A tyre service and auto repair shop with tire fitting places specific demands on compressed air: impact wrenches, inflation and blow-off run alternately and sometimes simultaneously, practically without a break during the season. This text follows up on the general guide Jak vybrat kompresor and focuses on which compressor to choose for a tyre service based on actual air consumption.

The most accurate way to verify the required output is to enter your own tools into the output calculator on the Kompresory page.

Open the calculator

Ventilek: How to choose an air compressor – output, pressure and tank size step by step 13:22

Video: How to choose an air compressor step by step. The video starts right at the chapter Tyre shop (8:02). Ventilek shows how to calculate air delivery, pressure and tank size, and goes through five workplaces. You can work it out straight away in the compressor selection calculator. The video is in Czech with English subtitles.

2:14 How much air and pressure your tools need 3:02 How to calculate air delivery and pressure 4:49 Air receiver and pressure switch 7:04 Car repair shop 8:02 Tyre shop 9:21 Paint shop 10:16 Joinery 11:17 Home workshop and garage

How much air tools in a tyre service consume

The basis for selection is the sum of the consumption of the tools you use. Approximate values according to our calculator are given in the table. The numbers in brackets indicate the operating pressure required by the given tool.

ToolAir consumptionPressure
Impact wrench 1/2"150 l/min6.3 bar
Impact wrench 3/4" to 1" (truck)350 l/min—
Inflating passenger car tyres60 l/min3 bar
Inflating truck tyres60 l/min8 bar
Blow gun120 l/min—

Quality tyre inflators and accessories are also suitable for inflating tools. You can find a wider selection here:

@kategorie@(/pneuhustice-a-prislusenstvi/)(8)(slider)

Normal operation: step-by-step calculation

Do not add up consumption as if everything were running at once. What matters is how often the tool is actually in operation. A typical daily workshop operation looks approximately like this:

  • Two impact wrenches often (60%). 2 × 150 l/min × 0.6 = 180 l/min.
  • Inflating often. Approximately 36 l/min.
  • Occasional blowing. Approximately 36 l/min.

The total comes to 252 l/min. With a reasonable 30% reserve, you need an air delivery of at least 330 l/min (the calculator rounds up to the nearest ten). The highest required pressure is 6.3 bar, so with a reserve that's 7.8 bar, meaning the machine should have at least 8 bar (standard piston machines have 10 bar).

For this range, a 400 V oil-lubricated compressor with a tank of at least 200 liters is suitable. A larger tank means less frequent motor starts and a smoother supply during impact wrench tightening.

330 l/minminimum air delivery for normal operation
7.8 barworking pressure with reserve
200 lrecommended tank

Suitable machines for everyday tire service operation — from piston compressors for daily tire changing to a more powerful variant for higher consumption:

@produkty@(/litinovy-pistovy-kompresor-gk420-22-200/)(/pistovy-kompresor-perfect-3-270/)(/litinovy-pistovy-kompresor-gk530-30-200/)(/kompresor-pro-line-expert-a49bp-3-200ct/)(/dvoustupnovy-kompresor-a49b-4-200ct/)(/sroubovy-kompresor-walter-sktg-5-5-500-sp-combo/)(/sroubovy-kompresor-spn-5-5-10dx-270/)(slider)

An example for normal operation is the cast iron piston WK430-3-0/200P with an air delivery of 340 l/min and a 200 l tank, or the more powerful ATMOS Perfect 3/270 with 408 l/min and a 270 l tank, which at this consumption level cycles on about six times per hour.

Tire-changing season: when a piston machine is no longer enough

In spring and autumn, the situation changes. Impact wrenches and inflation run practically non-stop, and blowing happens frequently. Consumption at that point jumps to approximately 432 l/min, and with a reserve to 570 l/min.

This is already a job for a screw compressor with a tank. It works smoothly and handles long continuous consumption without overheating. An example is the WALTER SKTG 5.5/500 SP COMBO with an air delivery of 850 l/min and a 500 l tank.

Attention: A piston compressor must not run without a break — it needs a run-to-rest ratio of approximately 3 : 1. In continuous operation during the season, it would overheat and its service life would drop rapidly.

Ventilek advises

If you are changing tyres at full speed throughout the season, a screw machine pays off even where it would otherwise seem oversized. A piston unit running without rest will end up costing you more in repairs and replacements.

A wider selection of machines for continuous operation can be found in the screw compressors category.

View screw compressors

Truck tyres

Servicing truck wheels has different requirements. Inflation requires 8 bar, so the machine must have at least 10 bar (8 + 1.5 = 9.5 bar). The calculator for such a service recommends a 500 l tank. A 1" impact wrench additionally draws around 350 l/min, which significantly increases the required air delivery.

  • Higher pressure. A machine of at least 10 bar due to inflation to 8 bar.
  • Large air delivery. A 1" impact wrench alone consumes 350 l/min.
  • Large tank or screw machine. Short impact peaks require a reserve of air.

Frequently asked questions

What compressor for a passenger car tyre service?
For normal daily operation with two impact wrenches, inflation and occasional blowing, a piston compressor on 400 V with an air delivery of at least 330 l/min and a tank of at least 200 l is sufficient.
When does a screw compressor pay off?
During the tyre-changing season, when the tools run almost continuously and consumption rises above 500 l/min. A piston machine would not withstand such operation without overheating.
What pressure do I need for inflating truck tyres?
Inflating itself requires 8 bar, so choose a compressor rated for at least 10 bar.
How do I calculate the required output precisely?
Enter the number of impact wrenches and how often they run into the calculator on the Compressors page — you'll get the air delivery and recommended pressure.

Summary

  • Add up consumption according to frequency of use. Don't calculate as if everything ran at once.
  • Add a 30% reserve. This applies to both air delivery and pressure.
  • Normal operation can be handled by a piston machine with a tank of at least 200 l on 400 V.
  • For seasonal peaks and truck tyres, use a screw compressor or a machine for higher pressure.

The fastest way to verify the right machine is the calculator on the Compressors page — just enter the number of impact wrenches and how often they run.