How to choose a compressor for a joinery workshop

For a joinery, carpentry workshop or furniture production, a compressor is the basic power source for staplers, nailers and blowing off sawdust. This text follows on from the main article Jak vybrat kompresor and shows a specific procedure for a workshop. You can then verify the power in the calculator on the Compressors page.

Open calculator

Ventilek: How to choose an air compressor – output, pressure and tank size step by step 13:22

Video: How to choose an air compressor step by step. The video starts right at the chapter Joinery (10:16). Ventilek shows how to calculate air delivery, pressure and tank size, and goes through five workplaces. You can work it out straight away in the compressor selection calculator. The video is in Czech with English subtitles.

2:14 How much air and pressure your tools need 3:02 How to calculate air delivery and pressure 4:49 Air receiver and pressure switch 7:04 Car repair shop 8:02 Tyre shop 9:21 Paint shop 10:16 Joinery 11:17 Home workshop and garage

What tools and what consumption they have

In a joinery, you will most often encounter fastening tools and blowing. The indicative values are based on our calculator and differ mainly in air consumption and required pressure rather than anything else.

  • Stapler or nailer. Consumption around 40 l/min, but requires a pressure of 7 bar. Without it, the fastener will not be driven in fully.
  • Blow gun. Around 120 l/min for cleaning surfaces and blowing off sawdust. Used only occasionally, but in short peaks.
40 l/minstapler / nailer
7 barrequired tool pressure
120 l/minblow gun

If you are still choosing the fastening tool itself, take a look at the range of pneumatic staplers and nailers.

@kategorie@(/sponkovace-a-hrebikovace--pneumaticke-provedeni/)(8)(slider)

Calculation step by step

You cannot simply add up the full consumption of all tools — they never all run at once and all the time. Real usage is taken into account, and a reserve is added.

Air consumption

Two staplers running approximately 60% of the time give around 48 l/min. Occasional blowing adds about 36 l/min to that. Together this is approximately 84 l/min.

With a 30% reserve, the required air delivery works out to at least 110 l/min (the calculator rounds up to the nearest ten). With four staplers, you get to 180 l/min.

Required pressure

The tools require 7 bar at the outlet. Approximately 1.5 bar is added for losses in the hose and the treatment unit, giving 8.5 bar. The machine should therefore be rated for at least 9 bar; common piston machines have 10 bar.

SetupRequired air deliveryMachine pressure
2 staplers + occasional blowingat least 110 l/minat least 9 bar
4 staplersat least 180 l/minat least 9 bar

Pressure and tank matter, not consumption

The consumption of fastening tools is low, so for a joinery workshop what matters is not the liters per minute, but the pressure and the volume of the air tank. With a small tank, the machine would switch on too often — more than 10× per hour — and would wear out quickly.

  • Tank of at least 100 l. Evens out demand during nailing and reduces the number of motor switch-ons.
  • 230 V power supply. A standard socket is usually sufficient for this type of operation, a three-phase connection is not necessary.
  • Noise level. For a workshop where work goes on all day, a quieter machine pays off. The operator's comfort is noticeable.

An example of a machine for all-day operation is the ATMOS Perfect 2,2/150 EX — 230 V, 310 l/min, 150 l tank, 72 dB, with two staplers it switches on about 8× per hour. You can find a selection of suitable piston compressors below.

@produkty@(/pistovy-kompresor-perfect-2-2-150-e/)(/kompresor-pro-line-extensive-a39bt-2-2-150cm/)(/kompresor-pro-line-a39bp-2-2-150vm/)(/kompresor-pro-line-extensive-a29bt-1-5-150cm/)(/litinovy-pistovy-kompresor-gk420-22-200a/)(/kompresor-pro-line-extensive-a29bt-2-2-200cm/)(slider)

Ventilek advises

Keep an eye on the oil. For oil-lubricated piston compressors, check the level and change it in time according to the manual — this way, cleaner air goes to the fastening tools and the machine lasts longer. You can always find which oil is suitable for the compressor in the documentation of the specific machine.

View piston compressors

Summary

  • Calculate the real consumption. Not the sum of all tools at full capacity, but based on the duration of use and with a 30% reserve.
  • Aim for 10 bar. Tools require 7 bar, add losses to that.
  • Choose a tank of at least 100 l (150 l for four staplers). You will reduce frequent switching and extend the service life.
  • For an all-day workshop, a quieter machine. Operator comfort pays off.

In the calculator on the Compressors page, enter the number of staplers and select a quiet machine — you will get a specific recommendation for your workshop.

Frequently asked questions

What compressor for a nail gun in a joinery workshop?
A nail gun requires 7 bar, therefore choose a machine for at least 9 bar (commonly 10 bar) with a tank of at least 100 l. Consumption is low, what matters is the pressure and the air tank volume.
Is a 230 V socket enough for me?
For operating staplers, nail guns and occasional blowing, usually yes. Three-phase connection is generally not necessary for this type of work.
Why isn't a small tank enough?
With an air tank under 100 l, the machine would switch on too often, more than 10× per hour, and would wear out quickly.
Which oil goes into a compressor?
For oil-lubricated machines, follow the manual of the specific compressor — the manufacturer states the oil type and the replacement interval there.