DRI pressure regulators with remote control for high flow rates

DRI pressure regulators by KNOCKS FLUID-Technik maintain a constant pressure even at high air consumption – up to 50,000 l/min. The pressure is not set on them by hand: the outlet pressure equals the pilot pressure that you feed into the regulator from a small pilot regulator. The pilot can be next to the operator or on a control panel, while the DRI sits directly in the pipework – under the ceiling, in the machine or in another hard-to-reach place.
They are diaphragm regulators with secondary venting: when you reduce the pilot pressure, they release the excess air from the outlet by themselves. Four body sizes cover flow rates of 5,800 to 50,000 l/min and threads from G 1/2" to G 2"; the inlet pressure is 25 or 40 bar depending on the version. For very precise control, there are the FDRI 03 precision regulators with a pilot stage: they hold the pressure with an accuracy of 5 mbar, control from 0.05 bar and deliver up to 6,500 l/min.
What the DRI regulators offer
- high flow rate at constant pressure – up to 50,000 l/min
- you set the pressure remotely with a pilot regulator; the regulator can be in an inaccessible place
- the outlet pressure equals the pilot pressure
- secondary venting – excess pressure at the outlet is released automatically
- with a feedback pilot, the pressure is held precisely even at high air consumption
- pilot air and pressure gauge connections G 1/4"
- inlet pressure 25 bar, most versions 40 bar
- zinc die-cast or aluminium body, NBR diaphragm and seals, operation from −10 to +80 °C
- FDRI 03 precision version: accuracy 5 mbar, control from 0.05 bar, operation from −35 °C and venting up to 800 l/min
Four body sizes
The size determines the flow rate. Within one size, all threads have the same flow rate and dimensions.
| Size | Codes | Threads | Flow rate | Inlet pressure | Control range | Dimensions | Weight |
|---|---|---|---|---|---|---|---|
| BG 3 | DRI33, DRI3340 | G 1/2" | 5,800 l/min | 25 / 40 bar | 0.5–16 / 0.5–20 bar | 82 × 74 mm | 0.85 kg |
| BG 5 | DRI54, DRI55 | G 3/4", G 1" | 15,000 l/min | 40 bar | 0.5–20 bar | 117 × 109 mm | 1.9–2.0 kg |
| BG 7 | DRI76, DRI77 | G 1 1/4", G 1 1/2" | 31,500 l/min | 40 bar | 0.5–20 bar | 119 × 123 mm | 2.2–2.3 kg |
| BG 8 | DRI87, DRI88, DRI8740, DRI8840 | G 1 1/2", G 2" | 50,000 l/min | 25 / 40 bar | 0.5–16 / 0.5–20 bar | 160 × 198 mm | 4.6–6.0 kg |
Flow rate according to the manufacturer. Dimensions: body length (inlet–outlet) × overall height.
All DRI and FDRI regulators
| Code | Thread | Flow rate | Inlet pressure | Control range | Size | Weight |
|---|---|---|---|---|---|---|
| DRI33 | G 1/2" | 5,800 l/min | 25 bar | 0.5–16 bar | BG 3 | 0.85 kg |
| DRI3340 | G 1/2" | 5,800 l/min | 40 bar | 0.5–20 bar | BG 3 | 0.85 kg |
| DRI54 | G 3/4" | 15,000 l/min | 40 bar | 0.5–20 bar | BG 5 | 2.0 kg |
| DRI55 | G 1" | 15,000 l/min | 40 bar | 0.5–20 bar | BG 5 | 1.9 kg |
| DRI76 | G 1 1/4" | 31,500 l/min | 40 bar | 0.5–20 bar | BG 7 | 2.3 kg |
| DRI77 | G 1 1/2" | 31,500 l/min | 40 bar | 0.5–20 bar | BG 7 | 2.2 kg |
| DRI87 | G 1 1/2" | 50,000 l/min | 25 bar | 0.5–16 bar | BG 8 | 5.0 kg |
| DRI88 | G 2" | 50,000 l/min | 25 bar | 0.5–16 bar | BG 8 | 4.6 kg |
| DRI8740 | G 1 1/2" | 50,000 l/min | 40 bar | 0.5–20 bar | BG 8 | 6.0 kg |
| DRI8840 | G 2" | 50,000 l/min | 40 bar | 0.5–20 bar | BG 8 | 6.0 kg |
| FDRI03 | G 1/2" | 6,500 l/min | 16 bar | 0.05–10 bar | BG 3 · FDRI | 1.2 kg |
| FDRI03-1 | G 1/2" | 6,500 l/min | 16 bar | 0.05–10 bar | BG 3 · FDRI | 1.2 kg |
FDRI 03 remote-controlled precision regulators

The FDRI 03 precision regulators work in the same way as the DRI – the outlet pressure equals the pilot pressure – but inside they have a pilot stage and a large diaphragm acting against a 13 mm valve seat. They therefore hold the pressure with an accuracy of 5 mbar, control from 0.05 to 10 bar and release the excess at up to 800 l/min through a G 3/8" port, which you can pipe away with a hose.
Connection G 1/2", flow rate up to 6,500 l/min, inlet pressure up to 16 bar, pilot connection G 1/8". The FDRI 03-1 also has a knob with which you fine-tune the outlet pressure by 0 to +1 bar above the pilot pressure – for example when one pilot controls several regulators and each needs a slightly different pressure.
| Code | Version | Accuracy | Control range | Pilot connection | Dimensions | Weight |
|---|---|---|---|---|---|---|
| FDRI03 | without knob, outlet = pilot pressure | 5 mbar | 0.05–10 bar | G 1/8" | Ø 82 × 108 mm | 1.2 kg |
| FDRI03-1 | with knob for fine adjustment by 0 to +1 bar | 5 mbar | 0.05–10 bar | G 1/8" | Ø 82 × 143 mm | 1.2 kg |
What to control the DRI regulator with
The pilot pressure is supplied by a pilot regulator. The most precise are the DRF precision regulators, which keep the pilot pressure constant even when the network pressure fluctuates. The feedback version measures the pressure downstream of the DRI regulator and compensates for it.
| Code | Control range | Feedback |
|---|---|---|
| DRF31-1GS | 0.1–1 bar | no |
| DRF31-3GS | 0.1–3 bar | no |
| DRF31-6GS | 0.2–6 bar | no |
| DRF31-10GS | 0.5–10 bar | no |
| DRF31-7FB | 0.2–7 bar | yes |
| DRF31-16FB | 0.5–16 bar | yes |
You will find all pilot regulators in the category DRF pressure regulators for pilot control. The pilot withstands an inlet pressure of no more than 16 bar – if the network pressure is higher, supply it from a branch with lower pressure. For the FDRI 03 precision regulators, the manufacturer recommends the feedback pilots DRF31-7FB or DRF31-16FB; the pilot connection is G 1/8". The pilot pressure can also be supplied by a proportional regulator controlled by an electrical signal.
How to choose a DRI regulator
- Size according to air consumption. Add up the air consumption of the machines downstream of the regulator. BG 3 handles 5,800 l/min, BG 5 15,000 l/min, BG 7 31,500 l/min and BG 8 50,000 l/min. At high air consumption, the outlet pressure drops slightly – the flow curves below show how.
- Inlet pressure according to the air network. Any DRI regulator is suitable up to 25 bar. If the network pressure is higher (up to 40 bar), choose the 40 bar version – see the table above.
- Outlet pressure. The 25 bar version controls 0.5–16 bar, the 40 bar version 0.5–20 bar. The actual pressure is determined by the pilot regulator – choose it according to the pressure you need (table above).
- Thread according to the pipework. Within one size, all threads have the same flow rate.
- Accuracy. If you need pressure accurate to a few mbar or control from as low as 0.05 bar, choose the FDRI 03 precision regulator (G 1/2", up to 6,500 l/min, inlet up to 16 bar). The FDRI 03-1 also has a knob for fine adjustment of the outlet pressure by 0 to +1 bar.
Example: a painting line needs 6 bar and 12,000 l/min, the regulator is to be installed under the ceiling and the network pressure is 10 bar. Size BG 5 is sufficient – with a G 1" connection, this is DRI55. You set the 6 bar pressure at the line with the pilot regulator DRF31-10GS (0.5–10 bar), most precisely with the feedback pilot DRF31-7FB. If a balancer needs exactly 4 bar and 5,000 l/min, choose the FDRI03 precision regulator with a feedback pilot.
Not sure which regulator to choose? Try the pressure regulator selector – based on line pressure, required pressure and flow.
#showmore#
How a remote-controlled regulator works

- You feed pilot air from the pilot regulator into the G 1/4" connection on the cover. The pilot pressure pushes on the diaphragm from above – just like the spring in a conventional regulator.
- The diaphragm opens the valve and air flows from the inlet to the outlet. The outlet pressure pushes on the diaphragm from below.
- When the outlet pressure equals the pilot pressure, the valve partially closes and only as much air flows through as is being consumed. The outlet pressure is therefore the same as the pilot pressure.
- When you reduce the pilot pressure, the diaphragm opens the vent hole and the excess air escapes from the outlet (secondary venting).
- A pilot with feedback measures the pressure downstream of the DRI regulator and adjusts the pilot pressure accordingly – the outlet then holds the pressure more precisely even at high air consumption.
- The FDRI 03 precision regulators have a G 1/8" pilot connection and a pilot stage inside: the pilot pressure sets the pilot stage, which in turn controls the large main diaphragm. They therefore hold the pressure more precisely than the DRI, at the cost of a small constant air consumption by the pilot stage.

Flow curves
The manufacturer’s graphs show how the outlet pressure drops as the flow rate increases at an inlet pressure of 8 bar. The lines start at a set pressure of 2, 4 and 6 bar (for size BG 8 also 1 bar). The flatter the line, the more stable the pressure at high air consumption. The graphs of the FDRI 03 (inlet 10 bar) and FDRI 03-1 (inlet 5 bar) show lines from 1 bar in steps of 1 bar.






Dimensions
Dimensional drawings from the manufacturer KNOCKS, dimensions in mm: body length (inlet–outlet) × overall height (as in the table above).




Installation and adjustment
- install a compressed air filter upstream of the regulator – dirt from the pipework would damage the valve seat
- connect the regulator with its inlet to the air network and its outlet to the consumers
- feed the pilot air from the pilot regulator through a hose or pipe into the G 1/4" connection on the cover – the pilot can be far away from the regulator
- set the pressure on the pilot regulator: the outlet pressure of the DRI follows it
- screw a pressure gauge for checking the outlet pressure into the G 1/4" gauge connection (the pressure gauge is not included)
- sizes BG 3 to BG 7 can be fixed to a wall with a bracket; size BG 8 is mounted directly in the pipework
- the FDRI 03 needs finely filtered (5 µm), oil-free air; feed the pilot air into the G 1/8" connection, the G 3/8" vent can be piped away with a hose, and the regulator is fixed to a wall with the BW30 bracket
Spare parts and accessories
The diaphragm in the regulator wears over time – replace it and the regulator will keep on working. Add a bracket when you mount the regulator on a wall.
| Part | Code | For regulators |
|---|---|---|
| spare diaphragm | MEMBRANEDRI33 | DRI33 |
| spare diaphragm | MEMBRANEDRI5540 | DRI54, DRI55 |
| spare diaphragm | MEMBRANEDRI7740 | DRI76, DRI77 |
| spare diaphragm | MEMBRANEDRI88 | DRI87, DRI88 |
| mounting bracket | BW30 | DRI33, DRI3340, FDRI03, FDRI03-1 |
| mounting bracket | BW50 | DRI54, DRI55, DRI76, DRI77 |
For the versions with a 40 bar inlet DRI3340, DRI8740, DRI8840, please ask us about the spare diaphragm.
You will find all parts for the regulators in the category spare parts and accessories for pressure regulators.
Specifications of the DRI series
| Parameter | Value |
|---|---|
| Inlet pressure | max. 25 bar (DRI33, DRI87, DRI88), max. 40 bar (others) |
| Outlet pressure (control range) | 0.5–16 bar (25 bar version), 0.5–20 bar (40 bar version) |
| Flow rate | 5,800 / 15,000 / 31,500 / 50,000 l/min (BG 3 / BG 5 / BG 7 / BG 8) |
| Adjustment | by pilot pressure from a pilot regulator, outlet pressure = pilot pressure |
| Pilot air connection | G 1/4" (female thread, on the cover) |
| Pressure gauge connection | G 1/4", pressure gauge not included |
| Secondary venting | yes |
| Operating temperature | −10 to +80 °C |
| Medium | compressed air, neutral gases |
| Material | zinc die-cast body (BG 3) or aluminium body (BG 5 to BG 8), NBR diaphragm and seals |
Specifications of the FDRI 03 and FDRI 03-1
| Parameter | Value |
|---|---|
| Connection | G 1/2" |
| Inlet pressure | max. 16 bar |
| Outlet pressure (control range) | 0.05–10 bar |
| Control accuracy | 5 mbar |
| Flow rate | 6,500 l/min |
| Adjustment | by pilot pressure, outlet pressure = pilot pressure; FDRI 03-1 also with a knob for fine adjustment by 0 to +1 bar |
| Pilot air connection | G 1/8" (female thread) |
| Pressure gauge connection | G 1/4", pressure gauge not included |
| Secondary venting | 800 l/min, exhaust via G 3/8" thread |
| Own air consumption | 1.7 l/min at an outlet pressure of 6 bar (max. 6.0 l/min at an inlet pressure of 16 bar) |
| Valve seat bore | 13 mm |
| Operating temperature | −35 to +60 °C |
| Medium | compressed air and neutral gases, finely filtered (5 µm), oil-free |
| Material | black-painted zinc die-cast body, NBR diaphragms and seals |
| Dimensions | FDRI 03: Ø 82 × 108 mm, FDRI 03-1: Ø 82 × 143 mm; depth 67 mm |
| Weight | 1.2 kg |
Ventilek advises
For the most precise pressure, use a pilot with feedback and connect the feedback as close to the point of use as possible. Put the pilot where the pressure can be set comfortably – the DRI regulator can stay under the ceiling.
- pilot regulators: DRF regulators
- manual adjustment and high flow rate: regulators 417 up to 25,000 l/min
- very precise control: FDR regulators
- pressure controlled by an electrical signal: proportional regulators
- Why does the DRI regulator have no handwheel for setting the pressure?
- The outlet pressure is determined by the pilot pressure that you feed into the regulator from a pilot regulator. So you set the pressure on the pilot – it can be next to the operator, while the DRI is under the ceiling or in the machine.
- Which pilot regulator should I choose?
- The most precise are the DRF precision regulators. For pressures up to 10 bar, DRF31-1GS to DRF31-10GS are sufficient; for the most precise control and pressures up to 16 bar, there are the regulators with feedback DRF31-7FB and DRF31-16FB. The pilot pressure can also be supplied by another pressure regulator.
- Is the pressure gauge included?
- No. The regulator has a G 1/4" gauge connection; the pressure gauge is ordered separately. The pilot pressure is shown by the pressure gauge of the DRF pilot regulator.
- What is the difference between the 25 and 40 bar versions?
- The 40 bar version withstands a higher network pressure and controls up to 20 bar, the 25 bar version controls up to 16 bar. Sizes BG 5 and BG 7 come in the 40 bar version.
- Why does air escape from the regulator when the pressure is reduced?
- That is secondary venting. When you reduce the pilot pressure, the regulator releases the excess air from the outlet and the pressure drops immediately, not only once air is consumed. A short hiss is therefore normal.
- Can I use the regulator for a gas other than air?
- The manufacturer specifies it for compressed air and neutral gases. For any other gas, please ask us before ordering.
- What is the difference between the DRI and the FDRI 03?
- Both are controlled by pilot pressure. The FDRI 03 also has a pilot stage: it is more precise (5 mbar), controls from 0.05 bar and works from −35 °C, but it needs finely filtered, oil-free air and consumes a little air (1.7 l/min at an outlet pressure of 6 bar). The DRI handles higher flow rates and a higher inlet pressure.
- What is the knob on the FDRI 03-1 for?
- With the knob, you fine-tune the outlet pressure by 0 to +1 bar above the pilot pressure. This is useful when one pilot regulator controls several regulators and each point of use needs a slightly different pressure.
Technical data according to the manufacturer KNOCKS FLUID-Technik (manufacturer’s website, for the FDRI 03 also the 2024 precision regulator brochure). DRI flow curves at an inlet pressure of 8 bar.
You will find more regulators in the category air pressure regulators.
Product sorting
List of products
KNOCKS remote-controlled diaphragm pressure regulator for high flow rates at constant pressure.outlet pressure = pilot pressure from a pilot regulator (G 1/4"...
KNOCKS remote-controlled diaphragm pressure regulator for high flow rates at constant pressure.outlet pressure = pilot pressure from a pilot regulator (G 1/4"...
KNOCKS remote-controlled diaphragm pressure regulator for high flow rates at constant pressure.outlet pressure = pilot pressure from a pilot regulator (G 1/4"...
Remote-controlled pressure regulator (volume booster) DRI by KNOCKS for high flow rates at constant pressure.controlled by pilot pressure from a pilot regulatorconnection G 1...
Remote-controlled pressure regulator (volume booster) DRI by KNOCKS for high flow rates at constant pressure.controlled by pilot pressure from a pilot regulatorconnection G 2",...
KNOCKS remote-controlled diaphragm pressure regulator for high flow rates at constant pressure.outlet pressure = pilot pressure from a pilot regulator (G 1/4"...
KNOCKS remote-controlled diaphragm pressure regulator for high flow rates at constant pressure.outlet pressure = pilot pressure from a pilot regulator (G 1/4"...
Remote-controlled pressure regulator (volume booster) DRI by KNOCKS for high flow rates at constant pressure.controlled by pilot pressure from a pilot regulatorconnection G...
KNOCKS remote-controlled diaphragm pressure regulator for high flow rates at constant pressure.outlet pressure = pilot pressure from a pilot regulator (G 1/4"...
KNOCKS remote-controlled diaphragm pressure regulator for high flow rates at constant pressure.outlet pressure = pilot pressure from a pilot regulator (G 1/4"...
KNOCKS precision pressure regulator, remotely controlled by pilot pressure, with a pilot stage and high venting capacity.outlet pressure = pilot pressure (G 1/8"...
KNOCKS precision pressure regulator, remotely controlled by pilot pressure, with a pilot stage and high venting capacity and a knob for fine adjustment.outlet pressure = pilot...