Screw compressor ATMOS Albert E.50 KV
Code: E.50KVProduct detailed description

Screw compressor ATMOS Albert E.50 KV
ATMOS Albert E.50 KV is a universal 5.5 kW screw compressor in the Komfort version — noise-reducing steel body + 270 l horizontal air receiver + LOGIK 26-S microprocessor control. The slow-running B100 block (1 455 min⁻¹) directly connected to a 4-pole motor ensures long service life and quiet operation of 64 dB(A) thanks to the body.
Working pressure 9 bar, delivery 870 l/min (0.87 m³/min) — the compressor typically serves a craft workshop with 4–6 pneumatic workstations simultaneously or a small production hall. Due to the combination of the slow-running block (longer service life) and the enclosure (installation in a standard workshop, not a plant room), this version is the most frequently chosen in this power class.
Configuration E.50 KV
Specifically, this variant consists of:

✓ Screw compressor
Always included — ATMOS screw block directly connected to the motor.

✓ Airman
270 l (horizontal)

— Air dryer
Not included (optionally addable)

— Inverter
Fixed-speed mode (start-stop)
Main features
Screw Block B100
Direct connection to the motor — minimum wear parts, long service life.
Enclosure 64 dB(A)
Noise-reducing steel enclosure — installation directly in the workshop between workbenches.
LOGIK 26-S control
Microprocessor control, ATMOS Care monitoring of service intervals.
5.5 kW · 0.87 m³/min
Working pressure 9 bar. Rated voltage 400 V / 50 Hz.
ATMOS Care Monitoring
Integrated service monitoring — tracking of engine hours and planned services.
Czech Manufacturer ATMOS
Chrást near Pilsen, manufacturing tradition since 1899. Service network throughout the Czech Republic.
Design and features of E.50 KV
The Comfort enclosure opens forward on two hinges — complete service access to all components within 30 seconds without tools. Inside the enclosure is an oil fill of 6 l, B100 injection block, 5.5 kW motor (IP 55-F, 11 A) and coolers for both compressed air and oil. A 270 l horizontal air receiver with an automatic condensate drain is positioned outside the housing.

Design and noise levels — 64 dB(A)
The noise level of 64 dB(A) is well below the industrial standard — the compressor can be installed directly in the workshop between workbenches, without the need for a separate plant room. The housing protects internal components from dust and mechanical damage and reduces disruptive noise for the operator. Cooling air inlet at the front, outlet at the rear — install at least 50 cm from the wall.
270 l pressure vessel
The 270 l air receiver in a horizontal layout is a standard solution for operations with 3–6 parallel workstations. For operations with higher peak demands (pneumatic pressing, large wrenches), the manufacturer offers an optional 500 l version. The air receiver is equipped with a safety valve (10 bar), a pressure gauge, an automatic condensate drain, and a ball valve.

Technical data E.50 KV
BASIC DATA — E.50 KV | |
|---|---|
| Screw block | B100 |
| Minimum working pressure | 5 bar |
| Maximum working pressure | 9 bar |
| Nominal capacity (ISO 1217) | 0.87 m³/min |
| Maximum block speed | 1,455 min⁻¹ |
| Nominal power of the main motor | 5.5 kW |
| Rated voltage | 400 V / 50 Hz |
| Motor protection class | IP 55-F |
| Nominal current (50 Hz) | 12.1 A |
| Noise level | 64 / 69 dB(A) (according to ISO 2151, ISO 3744 — with housing / open version) |
| Oil fill volume | 3.5 l |
| Oil content in compressed air | 2 – 4 mg/m³ (cartridge separator) |
| Compressed air outlet | G 1/2" |
| Weight | 270 kg |
| The temperature of the working environment | +5 ÷ +40 °C |
E.50 KV SPECIFICATION | |
| Housing | Comfort (soundproof steel housing) |
| Airman | 270 l (horizontal) |
| Integrated dryer | Not included (optional) |
| Control unit | LOGIK 26-S (microprocessor) |
| ATMOS Care | Integrated service interval monitoring |
| Guarantee | 7 years UNLIMITED — regardless of operating hours |
| Manufacturer | ATMOS Chrást, CZ (since 1899) |

Optional extras for E.50 KV
The machine can be supplemented with the following optional elements (on request):
- ATM Anti-condensation Management
- ATMOS R1 Proportional Control
- Compressor feet (version without air receiver)
- Fully synthetic oil
Who is the E.50 KV suitable for

The E.50 KV is the best-selling variant in the series — it is purchased by medium-sized craft workshops and car services with 4–8 workstations, who appreciate the quiet operation (installation in the workshop, not in the cellar), the dust-protecting housing, and LOGIK 26-S for planning service intervals. Typical customer: metal production with 5–10 employees, car service with a lift + tyre service, maintenance companies.
Typical applications
- Metal production 5–10 people — pneumatic drills, wrenches, grinders, pressing
- Car services with pneumatic wrenches and inflation stations
- Locksmith operations with pneumatic riveters and punchers
- Pneumatic conveyors for small parts (assembly lines)
- Pressure tests and calibration (laboratories, production of pneumatic components)
- Universal industrial operation with medium consumption (up to 6 m³/h)
- Woodworking companies — pneumatic staplers, nailers, blow-off

7-year UNLIMITED warranty — unique in the Czech Republic
"We simply trust our machines! The best way to express confidence in the quality of our machines is to provide a SEVEN-YEAR UNLIMITED WARRANTY."
- No flat-rate payments
- No service contracts
- 7 years worry-free
- 7 years of operational certainty
- Online management via the ATMOS Plus app
Machine control — LOGIK 26-S

The LOGIK 26-S microprocessor unit replaces the simple pressure switch in higher models of the series — the compressor is controlled via a structured menu on the front of the body. Activity logs (50 days of history), an operating hours counter, service interval planning (ATMOS Care), and optional remote management via the ATMOS Plus app are available.
- Operating hours monitoring for each compressor
- Communication station control
- Activity and fault logs
- Up to 50 days of records for each day and week
- Master/Slave mode for 2 compressors
- Data transfer via RS 485 - Modbus bus
Optional remote compressor management via internet (ATMOS Plus app) — monitoring, alerts and remote parameter setting.
Related models in the Albert range
- View all Albert models (overview 4-22 kW)
- ATMOS SEC — power class 15-37 kW (belt drive)
- ATMOS SMARTRONIC — top series 30-110 kW
Frequently asked questions
- What does the Standard vs Komfort version mean?
- Standard = open version without a housing. Komfort = machine in a soundproof steel housing that opens forward. The Komfort version achieves significantly lower noise levels and is more suitable for workshops and proximity to workplaces.
- What is the difference between the standard and Vario versions?
- The Vario version is equipped with a Danfoss inverter, which smoothly regulates the speed of the screw block and thus the machine performance according to current consumption. Main advantage: significant electrical energy savings by eliminating idling.
- What do the letters K, V, S in the model code mean (e.g. E.50 KVS)?
- K = Komfort (steel housing), V = air receiver (270 l standard), S = integrated condensing compressed air dryer. Example: E.50 KVS = E.50 in Komfort version with air receiver and dryer.
- What is ATMOS Care and why do I need it?
- ATMOS Care is an additional electronic unit that monitors the condition of filter elements and indicates when service is required. If replacement does not occur, the unit modifies the machine's performance so that it can continue to operate safely — thus protecting against damage caused by clogged filters.
- What is anti-condensation management (ATM) and when should it be chosen?
- ATM is a system that keeps the compressor permanently heated and removes water vapour from the inside of the machine. It is suitable for machines with short operating times and long periods of inactivity — without ATM, there is a risk of condensate formation and internal corrosion.
Additional parameters
| Category: | ALBERT |
|---|---|
| Compressor type: | Screw compressor |
| Version: | Screw compressor |
| Pressure: | 9 bar |
| Air delivery: | 870 l/min |
| Pressure vessel volume: | 270 L |
| Design of pressure vessel: | Lying down |
| Connecting: | 1/2" |
| Motor power: | 5.5 kW |
| Mains voltage: | 400/50 V/Hz |
| Lubrication: | Oleic |
| Noise: | 64 dB(A) |
| Warranty: | 7 years |
| Engine: | Electric |
| Soundproofed: | Yes |
| Drive: | Direct |
| Air dryer: | No |
| Retrieved from: | Professional |
| Development: | Stationary |
| Inverter: | No |
Product rating
Be the first who will post an article to this item!
ATMOS is a Czech family-owned compressor manufacturer, the company ATMOS Chrást s.r.o. from Chrást near Pilsen. It makes screw and piston compressors, its own screw blocks and generator sets, and besides stationary machines also mobile and locomotive compressors. It makes the blocks and air receivers itself, assembles and tests the machines in Chrást and exports them to more than 100 countries.
Engineering production in Chrást began in 1899, compressors have been made here for more than 70 years, and in 2024 the company celebrated its 125th anniversary. In the socialist era the works belonged to the state enterprise Škoda Plzeň; screw compressors arrived in the 1980s, at first under licence, and more than 25 new types have been added since. With us you will find the Perfect piston series for the workshop and the Albert, SEC and SmartTronic screw series for continuous operation.
Made in the Czech RepublicATMOS compressor series
Perfect — piston compressors
Cast-iron pump unit for the workshop. The cast-iron pump unit runs at low speed and copes with daily use. Since 2004 it has been working in tens of thousands of installations in the Czech Republic and abroad.
- 2.2 to 7.5 kW, 310 to 1,170 l/min
- horizontal or vertical receiver, 90 to 500 l
- two-stage machines for 12.5 and 14 bar
Albert — screw, 4 to 22 kW
From a small workshop to light production. The slow-running B100 or B150 screw block is coupled directly to the motor, with no belt.
- Komfort in a soundproof steel enclosure
- air receiver and dryer on the machine
- Vario with a frequency inverter
SEC — industrial, 22 to 37 kW
For continuous operation in production. A free-standing machine in a soundproofed steel enclosure, the air receiver is chosen separately.
- pressure 8, 10 or 13 bar
- IE3 motors and ATMOS screw blocks
- Vario with a frequency inverter
SmartTronic — 30 to 110 kW
A compressor station in one cabinet. The ATMOS flagship series for large industrial plants.
- free air delivery up to 19.1 m³/min
- pressure 7.5 to 13 bar
- FD version with a built-in fusion dryer
Service kits and oil
Everything for one service. Original kits for Perfect compressors for the 1st to 4th year, chosen by the machine’s pump unit.
- oil with extractor, filter elements, check valve parts
- for the 2nd and 4th year also valve plates and belt
- ATMOS VDL 100 oil for piston machines
Not sure whether you need a piston or a screw compressor? The selection calculator in the Compressors category will help you find the right output.
Choose a compressorATMOS series side by side
| Design, motor, pressure and equipment | ||||
|---|---|---|---|---|
| Series | Design | Motor | Pressure | Equipment |
| Perfect | piston, cast-iron pump unit | 2.2–7.5 kW | 10 · 12.5 · 14 bar | 90–500 l receiver, PFT version without receiver |
| Albert | screw, block directly on the motor | 4–22 kW | up to 13 bar | Komfort enclosure, receiver, dryer, Vario inverter |
| SEC | screw, free-standing | 22–37 kW | 8 · 10 · 13 bar | soundproofed enclosure, Vario inverter |
| SmartTronic | screw compressor station | 30–110 kW | 7.5–13 bar | FD fusion dryer, Vario inverter |
A piston compressor needs breaks; the air receiver gives it time to cool down. A screw compressor can run continuously.
How to choose an ATMOS compressor
1. Add up consumption
Add up the air consumption of the tools that will run at the same time and allow a reserve of about 30 %. Work with the machine’s free air delivery, not its intake capacity.
2. Piston or screw
For intermittent use in a workshop or garage, a Perfect piston compressor is enough. Where the compressor runs for most of the shift, choose an Albert, SEC or SmartTronic screw compressor.
3. Pressure and receiver
Most tools need 10 bar; the two-stage Perfect machines deliver 12.5 and 14 bar. A large receiver pays off when tools draw air in bursts: the machine then switches on less often.
4. Dry air and maintenance
For dry, clean air add a dryer and filters; on screw machines the dryer can be built into the compressor. Service a Perfect piston compressor once a year with an original service kit.
Frequently asked questions
- Who makes ATMOS compressors?
- The Czech family-owned company ATMOS Chrást s.r.o. at its plant in Chrást near Pilsen, where engineering production has been running since 1899. In the socialist era the plant belonged to the state enterprise Škoda Plzeň; from that time comes, for example, the 1982 PKD12 piston compressor under the ŠKODA brand. ATMOS makes its own screw blocks and air receivers, and assembles and tests the machines in Chrást.
- What does Vario in the name mean?
- A Vario machine has a frequency inverter that smoothly adjusts the speed of the screw block to the current air demand. The compressor does not run idle and, with variable demand, saves 20 to 30 % of electricity.
- What do the letters in the Albert series mean?
- K = Komfort in a soundproof steel enclosure, V = air receiver, S = built-in refrigeration dryer. For example, the E.50 KVS is an E.50 in the enclosure, with a receiver and a dryer.
- Which Perfect can I plug into a 230 V socket?
- The Perfect 2,2/90 EX and the Perfect 2,2/150 EX. The other Perfect compressors need a three-phase 400 V socket.
- Which oil goes into a Perfect compressor?
- ATMOS VDL 100 mineral compressor oil. Depending on the machine, the fill is 1 to 2 litres, and the oil comes with an extractor in every service kit.
- What is the FD fusion dryer in the SmartTronic series?
- A dryer built directly into the compressor that uses the machine’s waste heat for regeneration. You set the pressure dew point on the controller between +5 and −20 °C. The five largest models have no FD version.
The operating manual for Perfect compressors can be downloaded from the machine’s product page. ATMOS is a brand of ATMOS Chrást s.r.o.
| Manufacturing company : | ATMOS Chrást s.r.o. |
|---|---|
| Address : | Plzeňská 149, 330 03 Chrást, Czech Republic |
| E-mail : | info@atmos-chrast.cz |