High-pressure ABAC Tech compressor - ATH-2,2/30-BT motor 2.2 kW, 150 l/min at 30 bar, intake 252 l/min, on a base frame, supply 400/50 V/Hz, 99 dB Lwa / 79 dB at 4 m
Code: ATH-2-2/30-BT
Related products
Product detailed description
ABAC Tech ATH · 30 bar · direct startAn entry point into the category for anyone who just wants to set up the machine and connect it. ATH-2,2/30-BT is a two-stage unit on a steel support frame with a control panel, delivering 150 l/min at a full 30 bar and starting directly. It has no air receiver — the air goes into the distribution system or into your own tank certified for thirty bar.
Where the limit of direct starting lies
Up to 2.2 kW, the motor starts directly: the contactor closes and the machine runs. From 4 kW upwards it is marked with X in the code and starts via star-delta, because the current surge during direct start would be too much for a standard power supply. If your electrical distribution is weaker or the machine starts frequently, this limit matters more than the difference in output.
With the machine you get a support frame with mounting feet, a control panel with a main switch, and a pressure switch — it's set up, anchored and connected. The air receiver is not included, and no machine in this category has one; it must be your own and certified for thirty bar.
Equipment and details
What the ATH-2,2/30-BT offers from the factory
- two-stage oil-lubricated unit with two V-shaped cylinders, 1,500 rpm
- 2.2 kW motor in S1 85% mode — an industrial duty cycle with a short pause after roughly fifty minutes
- direct drive without belts — the unit sits directly on the motor
- mounted on a steel support frame with control panel; air receiver is not included
- 400/50 V/Hz electric motor, three-phase supply, direct start
- intake 252 l/min, delivery 150 l/min at an operating pressure of 30 bar
- intercooler between the low-pressure and high-pressure cylinder, stainless steel valves
- crankshaft bearings factory-filled with grease for the entire service life
- weight 73 kg, dimensions 686 × 575 × 671 mm; noise level 99 dB Lwa, at 4 m 79 dB
- 2-year warranty
Machine details
Where to go next if the ATH-2,2/30-BT isn't the right fit
Three-quarters more air is delivered by the ATH-4/30-BTX, and two and a half times more by the ATH-5,5/30-BTX. The full overview is in the overview of the entire category, and ten bar lower with a 100% duty cycle is the 20 bar range.
Delivery is the amount of air that the machine supplies at an operating pressure of 30 bar; intake is the volume drawn in by the low-pressure cylinder. Noise level is stated as the sound power level Lwa from the nameplate and as the sound pressure at 4 m from the machine. Performance data according to ISO 1217, annex C, noise level according to ISO 2151.
Ventilek's advice
Choose this machine if you don't want to deal with a star-delta starter. From four kilowatts upwards, this is mandatory equipment, along with the corresponding protection.
Additional parameters
| Category: | Air compressors |
|---|---|
| Warranty: | 2 years |
| Compressor type: | Piston compressor |
| Pressure: | 30 bar |
| Suction power: | 252 l/min |
| Air delivery: | 150 l/min |
| Pressure vessel volume: | It isn't |
| Motor power: | 2.2 kW |
| Mains voltage: | 400/50 V/Hz |
| Speeds: | 1500 rpm |
| Number of cylinders: | 2 |
| Number of grades: | 2 – two-stage compressor |
| Lubrication: | Oleic |
| Noise: | 99 dB - Lwa, 79 dB - Lwp(4m) |
| Dimensions: | 686 × 575 × 671 mm |
| Weight: | 73 kg |
| Engine: | Electric |
| Soundproofed: | No |
| Drive: | Direct |
| Air dryer: | No |
| Retrieved from: | Industrial |
| Development: | Stationary |
Product rating
Be the first who will post an article to this item!
Discussion
Be the first who will post an article to this item!
The company ABAC has been one of the most important manufacturers of piston compressors on the world market since its establishment in 1980 . Currently, the brand ABAC is owned by ATLAS COPCO, the largest compressor manufacturer in the world and is part of the multinational group PAD (Professional Air Division). The goal of the ABAC brand is to become a world leader in the development, production and sale of piston compressors.
Production at company ABAC
ABAC compressors are manufactured in 5 production centers around the world, with an annual production of almost 2 million compressors. The brand's parent plant ABAC in Turin, Italy employs around 250 employees and is primarily focused on the design and production of professional V-belt compressors with a daily production capacity of over 600 machines. The ABAC plant also has extensive warehouse facilities with several thousand compressors available for immediate delivery.
Innovative concept
ABAC does not only mean compressor production. We are directly involved in the development of key innovations and advanced solutions and set trends in the compressor market. The efforts of our designers have resulted in, for example, an aerodynamic pulley housing for temperature reduction of up to 35°C, the revolutionary XPAND hose reel compressor or the PRO LINE ZERO oil-free compressors with V-belts. In the ABAC program you will always find the most modern and unique solution for compressed air production on the market.
A modern solution
We are a modern company that is aware of the current trends around us. We are bringing advanced technologies to the compressor industry, such as the use of QR codes and the AIR TUBE app to make it easier for the user of our compressor to access the information they need. We use social media, chat and multimedia instead of traditional marketing and documentation formats. With compressors ABAC you will always have convenient access to all the necessary information.
Compressor program
In the supplier program of the ABAC brand you will find 100%. The basic range includes 100% from small portable compressors for home applications to larger stationary compressors for permanent deployment.
