Compressor spare parts and accessories, Page 5
.png)
Product sorting
List of products
Non-original complete filter with cover and filter insert in round design with 1/2" male pipe thread. The suction filter serves as protection against dirt entering the machine...
A twenty-litre canister for continuous duty. One change a year instead of four — filters and separator included.
Non-original complete filter with cover and filter insert in round design with 3/8" male pipe thread. The suction filter serves as protection against dirt entering the machine...
Replacement non-return valve for piston compressor. Connection to the air tank, 1/4" external thread. Connection to the compressor external thread 3/8". Viton seal. Prevents...
A five-litre canister for compressors running several shifts. One pack covers a full change even on the largest ABAC piston machines.
A two-stage pump on the A-series pulley — the step between workshop and industrial duty. Higher pressure than the single-stage pumps and more efficient compression.
The advanced service kit for the two-year service of an ABAC piston compressor with the A29, A29B, A29B0, A39, A39B, A39B0 pump unit. Over the basic kit it adds the valve plate...
A replacement oil sight glass for a compressor with a G 3/4" pipe thread. Outer diameter 31.5 mm, window 20 mm, tightened with a 27 mm spanner. Transparent PA-T technopolymer...
The advanced service kit for the two-year service of an ABAC piston compressor with the A49B pump unit. Over the basic kit it adds the valve plate and the gasket set — this is...
A drum of genuine SCR lubricant for plants with several machines. The lowest price per litre in the range, but it needs a stand and a pump.
The genuine SCR lubricant in the smallest canister. On a machine under warranty it is the only choice the manufacturer accepts.
The TD25M timed drain with a solenoid valve opens at a set interval (0.5–45 min) for a set time (0–10 s). Brass body, 230 V AC, up to 25 bar.
A slow-running version with output close to the B70 but at lower speed. Lower speed means less wear and smoother running at comparable output.
The suction filter for ABAC B59 and B60 compressors serves as a protection against the ingress of dirt into the machine unit and should be replaced or cleaned regularly. ABAC...
The TD150M timed drain with a solenoid valve opens at a set interval (0.5–45 min) for a set time (0–10 s). Brass body, 230 V AC, up to 150 bar.
A twenty-litre canister of certified oil for food plants. The usual choice for one line with its own screw compressor.
The only oil in the ABAC range listed for industrial piston and screw machines alike. The one-litre bottle suits topping up rather than a full change.
Suction filters serve as protection for the ABAC B70 compressor against dirt entering the machine and should be replaced regularly. ABAC compressors are supplied with suction...
A heavily additised oil with twice the interval of the basic Rotair. A five-litre canister for smaller machines or for topping up.
A five-litre canister of the highest ABAC oil for piston machines. Unlike the one-litre bottle this is a pack for a full change, not just for topping up.
Original ATMOS service kit N770405 for servicing Perfect 4T piston compressors after 2 years of operation. Major service: besides the oil, filter cartridges and check valve...
Original ATMOS service kit N770406 for servicing Perfect 4T and 4VT piston compressors after 3 years of operation. It contains ATMOS VDL 100 oil with an extractor, air filter...
Original ATMOS service kit N770407 for servicing Perfect 4T piston compressors after 4 years of operation. Major service: besides the oil, filter cartridges and check valve...
Original ATMOS service kit N770408 for servicing Perfect 4VT piston compressors after 2 years of operation. Major service: besides the oil, filter cartridges and check valve...
Original ATMOS service kit N770409 for servicing Perfect 4VT piston compressors after 4 years of operation. Major service: besides the oil, filter cartridges and check valve...
A zero-loss electronic condensate drain with a capacitive sensor for receivers, dryers and filters. It opens only when there is something to let out, so not one litre of...
A float condensate drain for filters, pressure vessels and cyclone separators. It works mechanically, without electricity and without setting. Body made of stainless steel.
A float condensate drain for filters, pressure vessels and cyclone separators. It works mechanically, without electricity and without setting. Body made of brass.
A float condensate drain for filters, pressure vessels and cyclone separators. It works mechanically, without electricity and without setting. Body made of stainless steel.
The suction filter for compressors ABAC with the A49B unit serves as protection against dirt entering the machine unit and must be replaced or cleaned regularly. ABAC...
A manual condensate drain for filters, pressure vessels and cyclone separators. Stainless steel build, with no electronics and no moving parts that could seize.
An oil safe for incidental contact, certified NSF H1, halal and kosher. For plants where the compressed air meets the product.
A drum of the top Rotair range. For plants with several machines running continuously in heat or in dust.
The top oil of the Rotair range in a five-litre canister. The only one the manufacturer allows into compressor rooms above 40 °C and into very dusty plants.
The stronger sibling of the A29 on the same pulley. Same installation envelope, higher output — the one to pick when the existing block has stopped keeping up and the motor and...
Suction filters serve as protection for the ABAC BV89 compressor against dirt entering the machine and should be replaced regularly. ABAC compressors are supplied with suction...
The TD420M-230VAC timed drain with a solenoid valve opens at a set interval (0.5–45 min) for a set time (0–10 s). Stainless steel body, 230 V AC, up to 420 bar.
The TD420M-24VDC timed drain with a solenoid valve opens at a set interval (0.5–45 min) for a set time (0–10 s). Stainless steel body, 24 V DC, up to 420 bar.
The TD50M timed drain with a solenoid valve opens at a set interval (0.5–45 min) for a set time (0–10 s). Brass body, 230 V AC, up to 50 bar.
A two-stage pump for higher draws — several workstations at once, or one more demanding tool.