M7 air-powered pneumatic tools
Powerful pneumatic tools that do not waste compressed air - the dream of every workshop, tyre workshop or engineering company. You can do it with M7 tools, among the best on the market - and that's all thanks to more than 20 years of experience and innovation. It will delight you not only with its performance, but also with its durability and simple operation, which you will appreciate in every DIY moment, but also in business. At Mighty Seven, every new pneumatic tool is rigorously tested under the most demanding operating conditions in the company's laboratories. And we offer you a free trial of the tools with your subsequent order! Further information to help you make your choice can be found later in the text.
#ShowMore#
Once you have an air compressor or compressed air supply in your workshop, you can make manual work easier with pneumatic tools. Connection is easy - just clip the tyre tool onto the hose quick coupling and you're ready to work. We advise you not to buy cheap pneumatic tools from China, because unlike quality products, they have a much higher consumption of compressed air - the operation will become very expensive over time.
What you can do with air tools
- loosen and tighten the screws
- grind and polish the surface
- cut and cut
- drill holes and create burrows
- mow
- drill
- to rivet
- staple and nail
- inflate wheels or balls
- measure torque
- lubricate under pressure
- press
Don't forget about air conditioning
But what good are all the accessories for a compressor if it is fed with poor quality and dirty compressed air, which would cause the tool to be in the workshop more often than in your workshop or plant? Whether it is mechanical dirt, condensate or oil vapours, it is always a good idea to try to prevent their effect on all accessories. For this reason, various air treatment systems are connected behind the compressor:
- Compressed air treatment units
- Compressed air filters - industrial filtration ISO 8573
- Compressed air dryers - condensing, adsorption, membrane
- Cyclone separators
- Separators for water/oil separation
By connecting these devices behind the compressor, you will increase the life of each connected tool. You eliminate the possibility of internal corrosion or galling. You will soon get a return on your investment. Not to mention the joy of using air tools without any problems!
Lubrication of pneumatic tools
Another important issue for the proper functionality of any pneumatic tool is the need for proper lubrication. You will avoid increased friction, which results in increased temperature and thus material expansion and a tendency to stick.
How to ensure lubrication? There are several ways:
- adding a lubricator/oiler between the tool and the air hose, an easy and effective solution
- owning a compressor with an already integrated lubrication system
- add oil manually to the inlet, as a matter of principle it must be oil for air motors
Oilers for pneumatic tools
What else you can use with air tools :
-
Impact wrenches; pneumatic design
-
Ratchet wrenches; pneumatic design
-
Nuts for tighteners; cast iron
-
Shank grinders; pneumatic design
-
Angle grinders; pneumatic design
-
eccentric grinders; pneumatic design
-
Sheet metal cutters; pneumatic design
-
Car body saws; pneumatic design
-
Drills; pneumatic design
-
Screwdrivers; pneumatic design
-
Chopping hammers; pneumatic design
-
Riveting pliers; pneumatic design
-
Staplers and nailers; pneumatic design
-
Pressure lubricators; pneumatic design
-
Balancers; professional design M7
-
Other tools; pneumatic design
Product sorting
List of products
Pneumatic staple gun for frequent professional use; handle with non-slip rubber coating for good grip during work. Designed for wide buckles with a shank width of 10 mm and a...
Mineral oil for lubrication of pneumatic tools. Special viscosity specifically for compressed air driven tools. Branded oil manufacturer with safety data sheet available....
Small regulator for mounting on spray guns with max. pressure 11 bar, 1/4" thread and 40 mm pressure gauge.
Hardened nuts with shortened height for high tightening torques. For impact wrenches with 1/2" clamping square for 10 mm screws.
Filter for mounting on spray guns and pneumatic tools with a maximum pressure of up to 16 bar and a filtration capacity of 20 µm and 1/4" thread.
Grinding belt for belt grinders 1 pcs. QB-313P58- 30 x 540 mm roughness *80.
Airbrush in practical set with vinyl hose, containers, tightening wrench, dropper and feeding adapter. Adjustable coating width from 6 to 40 mm. Air inlet 1/4" with special...
The extension allows the loosening of very deep and hard-to-reach bolts and nuts. Extension of 125 mm for nuts with 1/2" square clamping. The outer square is equipped with a...
original lubricant in tube with application attachment; intended for lubrication of internal parts of M7 pneumatic tools.
Hardened nuts for high tightening torques. For impact wrenches with 1/2" clamping square for 8 mm screws.
Hardened nuts for high tightening torques. For impact wrenches with 1/2" clamping square for 10 mm screws.
Extended hardened nuts for high tightening torques. For impact wrenches with 1/2" clamping square for 11 mm screws.
Extended hardened nuts for high tightening torques. For impact wrenches with 1/2" clamping square for 15 mm screws.
Miniature oilers for direct mounting on 1/4" air tool inlet threads . Placement directly on the tool improves oil dispersion in the compressed air. Possibility of adjusting the...
Hardened nuts for high tightening torques. For impact wrenches with 3/4" clamping square for 23 mm screws.
Extended hardened nuts for high tightening torques. For impact wrenches with 1/2" clamping square for 19 mm screws.
Riveting pliers in a handy case with rivet samples, mounting keys, spare o-rings and springs and a compressed air-powered connection nipple.
Hardened nuts with shortened height for high tightening torques. For impact wrenches with 1/2" clamping square for 16 mm screws.
Extended hardened nuts for high tightening torques. For impact wrenches with 1/2" clamping square for 13 mm screws.
Extended hardened nuts for high tightening torques. For impact wrenches with 1/2" clamping square for 24 mm screws.
Hardened nuts for high tightening torques. For impact wrenches with 1/2" clamping square for 26 mm screws.
Hardened nuts for high tightening torques. For impact wrenches with 1/2" clamping square for 21 mm screws.
Set of 2 saw blades with 18 teeth/inch as an accessory for the body straight saw.
Hardened nuts for high tightening torques. For impact wrenches with 1/2" clamping square for 27 mm screws.
Hardened nuts with shortened height for high tightening torques. For impact wrenches with 1/2" clamping square for 14 mm screws.
Hardened nuts with shortened height for high tightening torques. For impact wrenches with 1/2" clamping square for 9 mm screws.
Hardened nuts for high tightening torques. For impact wrenches with 1/2" clamping square for 20 mm screws.
Spring balancer for suspension of pneumatic tools with a load capacity of 1.5 to 3.0 kg and a stroke of one metre.
Replacement pad 125 mm diameter with Velcro for EG-125 grinder.
Hardened nuts for high tightening torques. For impact wrenches with 1/2" clamping square for 11 mm screws.
Set of 5 hexagon chisels 10 mm for pneumatic chisel hammer AH-9150K.
Extended hardened nuts for high tightening torques. For impact wrenches with 1/2" clamping square for 17 mm screws.
Hardened nuts with shortened height for high tightening torques. For impact wrenches with 1/2" clamping square for 11 mm screws.
Hardened nuts with shortened height for high tightening torques. For impact wrenches with 1/2" clamping square for 12 mm screws.
Clamping spring for pneumatic hammers M7 SC-221C and SC-222. Can be exchanged for other sockets, extensions and springs.
Hardened nuts for high tightening torques. For impact wrenches with 1/2" clamping square for 18 mm screws.
Extended hardened nuts for high tightening torques. For impact wrenches with 1/2" clamping square for 10 mm screws.
Hardened nuts with shortened height for high tightening torques. For impact wrenches with 1/2" clamping square for 18 mm screws.
Spring balancer for suspension of pneumatic tools with a load capacity of 0.5 to 1.5 kg and a stroke of one metre.
SN-3121: robust hammer for heavy-duty chopping work, open-handled version. Chisels and scrapers with hexagonal shank 17,2 × 71,5 mm, clamping with chuck. Working pressure 6.3...