Filtration, regulation and treatment of compressed air, Page 15

AAFM pre-filter in 2 1/2" design to remove fine impurities up to 0.1 um from compressed air according to ISO 8573-1 class 2. Body with easily removable container and designed...

Mounting angle for compressed air treatment units in Combibloc design from EWO.

Controller diaphragm for compressed air treatment units in Combibloc design from EWO.

Protective basket for compressed air treatment units in Combibloc design from EWO.

Catalytic filters (hopcalite) AAFH2 in 1/2" design for removal of CO andCO2 to breathable air level according to ISO 8573-1 class 1. Body with easily removable container and...

Connection cable 5 m - with straight connector designed for proportional DRPE controllers. Operating temperature -10 to +60 °C. Electrical protection IP65. Connection - 4-pole...

High flow silencer with external pipe thread G 3/4" designed especially for compressed air expansion during regeneration and ventilation of adsorption dryer production columns....

Cyclone separator CHP1 with threaded connection 1 1/2". It enables inexpensive and efficient removal of water and impurities from compressed air. Working pressure 100 bar,...

Regulator for pressure reduction of compressed air and other non-volatile and non-toxic gases with inlet G 3/4" and outlet pressure regulation 0,5 - 25 Bar. Maximum inlet...

Regulator with inlet up to 25 bar 3/8" thread for pressure reduction of compressed air and other non-volatile and non-toxic gases. Control range 0.5 to 16 bar up to a flow rate...

Cyclone separator CHP1 with threaded connection 1/2". It enables inexpensive and efficient removal of water and impurities from compressed air. Working pressure 100 bar, working...

Cyclone separator CHP1 with 1/4" threaded connection. It enables inexpensive and efficient removal of water and impurities from compressed air. Working pressure 100 bar, working...

The extremely quiet and dust-free operation of the compressed air condensation dryer up to a flow rate of 600 m³/hr from the compressor at a 3°C dew point enables use in...

AAFC cyclone separator in 3" design with a flow rate of 36,000 l/min for partial removal of condensate from compressed air. Here the flow changes to rotational and due to the...

AAFB 1" coarse filter for removal of the largest mechanical impurities up to 15 um from compressed air according to ISO 8573-1 class 7. Body with easily removable container and...

Adsorption filter with activated carbon AAFA2 in 1 1/2" version for absorption of residual oil, oil vapours and aerosols with < 0,005 mg/m3 from compressed air according to ISO...

The extremely quiet and dust-free operation of the compressed air condensation dryer up to a flow rate of 72 m³/hr from the compressor at a 3°C dew point enables use in...

The ADRY-12 series adsorption dryer has been designed for continuous separation of water vapour from compressed air at flow rates up to 200 l/min. Reduces the pressure dew point...

High-flow silencer with external pipe thread G 1 1/4" designed especially for compressed air expansion during regeneration and ventilation of production columns of adsorption...

AAFA activated carbon filter in 1/4" version for absorption of residual oil, oil vapours and aerosols with < 0,005 mg/m3 from compressed air according to ISO 8573-1 class 1....

40 micron filter insert for compressed air treatment units in Combibloc design from EWO.

Connection set of FUTURA air handling units with wall bracket size 4. The kit can be used to connect any 2 modules of a given size together without the need for screws and other...

Fixing bracket with screws under the cover of the FUTURA size 1 unit. All modules of FUTURA units can be mounted in this way. Easily mounted with wall bracket and similar mounting.

Filter cartridge for medical vacuum filter MVAC-0006. Applications mainly in medical devices. Working pressure 20 to 2000 mbar, maximum flow up to 60 l/min.

Filter cartridge for medical vacuum filter MVAC-0016. Applications mainly in medical devices. Working pressure 20 to 2000 mbar, maximum flow up to 36 l/min.

Cyclone separator CHP1 with 3/8" threaded connection. It enables inexpensive and efficient removal of water and impurities from compressed air. Working pressure 100 bar, working...

The ADRY-75 Series Adsorption Dryer was designed for continuous separation of water vapor from compressed air at flow rates up to 1,250 l/min. Reduces the pressure dew point...

High-flow silencer with external pipe thread G 2" designed especially for compressed air expansion during regeneration and ventilation of adsorption dryer production columns....

The ADRY-200 Series Adsorption Dryer was designed for continuous separation of water vapor from compressed air at flow rates up to 3,333 l/min. Reduces the pressure dew point...

Pressure regulator with 5 um air filtration for compressed air with or without oil and for neutral gases up to 16 bar. Design according to ATEX II 2G2D. The adjusting pin can be...

The ADRY-150 Series Adsorption Dryer was designed for continuous separation of water vapor from compressed air at flow rates up to 2,500 l/min. Reduces the pressure dew point...

Stainless steel cyclone separator IHP2 with threaded connection 1 1/2". It enables inexpensive and efficient removal of water and impurities from compressed air. Working...

Stainless steel cyclone separator IHP2 with 1 1/4" threaded connection. It enables inexpensive and efficient removal of water and impurities from compressed air. Working...

Stainless steel cyclone separator IHP2 with 1" threaded connection. It enables inexpensive and efficient removal of water and impurities from compressed air. Working pressure...

Stainless steel cyclone separator IHP2 with threaded connection 1/2". It enables inexpensive and efficient removal of water and impurities from compressed air. Working pressure...

Stainless steel cyclone separator IHP2 with 2" threaded connection. It enables inexpensive and efficient removal of water and impurities from compressed air. Working pressure...